参数资料
| 型号： | MIC74BQS |
| 厂商： | Micrel Inc |
| 文件页数： | 5/18页 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER I2C 8B 16QSOP |
| 标准包装： | 98 |
| 接口： | I²C，SM 总线 |
| 输入/输出数： | 8 |
| 中断输出： | 是 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 管件 |
Micrel, Inc.
MIC74
October 2006
13
M9999-101006
Initializing the MIC74
The MIC74’s internal registers are reset to their default
state at power-on. The MIC74’s default state can be
summarized as follows:
All I/O’s configured as inputs (DIR = 00h)
Output configuration set to open-
drain(OUT_CFG = 00h)
All outputs high/floating (DATA = FFh)
Fan functions disabled (FAN_SPEED =
00h,FAN bit of DEV_CFG = 0)
All interrupts masked (IE bit of DEV_CFG = 0)
The result of this configuration is that all I/O pins will
essentially float unless driven by external circuitry. Any
system using the MIC74 will need to initialize the internal
registers to the state required for proper system
operation. The recommended order for initializing the
MIC74’s registers is as follows:
Write desired output
values to DATA
Set output configuration
in OUT_CFG
Set desired I/O's as
outputs by writing DIR
Set initial fan speed in
FAN_SPEED
(if using)
Read STATUS
to clear it
Write DEV_CFG to
turn on fan (if using)
Initialize for
polling
Initialization
complete
Figure 9a. Initializing the MIC74 for Polled Operation
1. Write DATA
2. Write OUT_CFG
3. Write DIR
4. Write FAN_SPEED (if using fan mode)
5. Write INT_MASK (if using interrupts)
6. Read STATUS to clear it.
7. Write DEV_CFG to enable fan mode and/or
interrupts, if using
At the conclusion of step three, any I/O’s configured as
outputs in step two will be driven to the levels
programmed into the data register in step one. The order
of step 1 through step 3 is important to insure that
spurious data does not appear at the I/O’s during
configuration. Following step 7, programming the device
configuration register, the MIC74 will begin generating
interrupts if they are enabled, and the fan will be started
if FAN_SPEED contains a nonzero value. The corresp-
onddding interrupt service routines (if any) must be
initialized and enabled prior to step seven. STATUS
should be cleared (step 6) in both polled and interrupt
driven systems.
Write desired ouput
values to DATA
Set output configuration
in OUT_CFG
Set desired I/O's as
outputs by writing DIR
Set initial fan speed in
FAN_SPEED
(if using)
Write INT_MASK to
enable interrupts
(if using)
Read STATUS to
clear it
Write DEV_CFG to
turn on interrupts
and fan (if using)
Initialize for
interrupts
Initialization
complete
Figure 9b. Initializing the MIC74 for Interrupts
相关PDF资料 |
PDF描述 |
|---|---|
| EXPANDIO-USB-PT-FS | IC I/O EXPANDER USB 32B 44TQFP |
| MAX7300ATL+ | IC I/O EXPANDER 2WIRE 40TQFN |
| MAX7300ATL+T | IC I/O EXPANDER 2WIRE 40TQFN |
| MAX7300AAX+T | IC I/O EXPANDER I2C 28B 36SSOP |
| PCA9698DGG,518 | IC I/O EXPANDER I2C 40B 56TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC74BQS TR | 功能描述:IC I/O EXPANDER I2C 8B 16QSOP RoHS:否 类别:集成电路 (IC) >> 接口 - I/O 扩展器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:74 系列:- 接口:I²C，JTAG 输入/输出数:9 中断输出:无 频率 - 时钟:400kHz 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:管件 包括:EEPROM |
| MIC74BWM | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MIC74YQS | 功能描述:接口-I/O扩展器 2-Wire Serial I/O Expander & Fan Controller, QSOP-16 - Lead Free RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| MIC74YQS TR | 功能描述:接口-I/O扩展器 2-Wire Serial I/O Expander & Fan Controller, QSOP-17 - Lead Free RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| MIC79050 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Simple Lithium-Ion Battery Charger Preliminary Information |
发布紧急采购，3分钟左右您将得到回复。