参数资料
| 型号： | MIC9131BQS |
| 厂商： | Micrel Inc |
| 文件页数： | 16/19页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR DC-DC PWM HV HS 16-QSOP |
| 标准包装： | 98 |
| 应用： | 控制器，电信 |
| 输入电压： | 9 V ~ 18 V |
| 输出数： | 1 |
| 输出电压： | 4.7 V ~ 5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 管件 |
MIC9131
If the current sense transformer were not used, the sense
resistor would dissipate 1.7 watts.
Micrel, Inc.
secondary winding inductance for the ?yback
topology)
R SENSE = =
V SENSE
I SENSE
0 . 82
5
= 0 . 164 ?
M2 is the inductor current downslope
For a boost topology, the inductor downslope is:
R1
di V ? V IN + V D
M 2 = = OUT
M 2 REFLECTED = M 2 ×
P DISS = I RMS 2 × R SENSE = 3 . 25 2 × 0 . 164 = 1 . 7 W
Slope Compensation
Power supplies using peak current mode control techniques
require slope compensation when they are operating in
continuous mode and have a duty cycle greater than 50%.
Without slope compensation, the duty cycle of the power sup-
ply will alternate wide and narrow pulses commonly referred
to as subharmonic oscillations. Even though the MIC9131
operates below a 50% duty cycle, slope compensation adds
the bene?ts of improved transient response and greater
noise immunity in the current sense loop (especially when
the current ramp is shallow). Slope compensation can be
implemented by adding an optimum 1/2 of the inductor cur-
rent downslope, re?ected back to the current sense input. In
real world applications, 2/3 of the inductor current downslope
is used to allow for component tolerances.
Slope compensation at the ISNS input may be implemented
by using a resistor and capacitor as shown in Figure 12. The
rectangular waveshape of the gate drive output is integrated
by the resistor/capacitor ?lter, which results in a ramp used
for the slope compensation signal. When the gate drive and
the current signal at the sense resistor goes low, the capaci-
tor is discharged to 0V.
Gate Drive
(pin 16)
MIC9131 R2
I SNS
(pin 14)
dt L
In a transformer isolated topology, the downslope must be
re?ected back to the primary by the turns ratio of the trans-
former. The re?ected downslope is:
Ns
Np
where : Ns/Np is the turns ratio of the secondary winding
to the primary winding.
M2 REFLECTED is the inductor curent downslope
re?ected to the secondary side of the current
sense transformer.
The re?ected downslope is multiplied by the current sense
resistor to obtain the downslope at the current sense input
pin (ISNS).
I SNS _ SLOPE = M 2 REFLECTED × R S
where Rs is the value of the current sense resistor.
The required downslope of the compensation ramp at the
ISNS input is:
M 3 = I SNS _ SLOPE × 0 . 67
R1 is know if a value for the resistor between the current
sense resistor and the Isns pin, has already been selected.
If not chose a value of 1k, which will minimize any offset
and signal degradation at the ISNS pin. Select a value of
C1 to minimize signal degradation from the cutoff frequency
of R1/C1. The bandwidth should be at least six times the
switching frequency.
C1
R SENSE
C 1 =
1
2 × π × f S × R 1
M 3 = V GATE_DRIVE ×
×
V GATE _ DRIVE × R 1
M 3 × C 1
di V + V D
M 2 = = O
Figure 12
The procedure outlined below demonstrates how to calculate
the component values.
Compute the inductor current downslope as seen at the cur-
rent sense input.
For a ?yback, buck or forward mode topology the
inductor downslope is equal to:
dt L
where :
V O is the output voltage
V D is the forward voltage drop of the recti?er diode
L is the inductance of the output inductor (or the
where: f S is the switching frequency of the power
supply (not the oscillator frequency)
The slope of the generated compensation ramp is:
R1 1
R2 + R1 R2 × C1
Solving for R2 and assuming R2 is much greater than R1.
R 2 =
where: V GATE_DRIVE is the amplitude of the gate
drive waveform
M9999-080206
16
August 2006
相关PDF资料 |
PDF描述 |
|---|---|
| P1812R-392K | INDUCTOR POWER 3.9UH SMD |
| ACM12DRKF | CONN EDGECARD 24POS DIP .156 SLD |
| P1812R-683K | INDUCTOR POWER 68UH SMD |
| ABM12DRKF | CONN EDGECARD 24POS DIP .156 SLD |
| RBM43DCAD-S189 | CONN EDGECARD 86POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC9131BQS TR | 功能描述:IC CTRLR DC-DC PWM HV HS 16-QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| MIC9131YM | 功能描述:电流型 PWM 控制器 SO-16 High Vin Telecom DC/DC PWM Control IC (Lead Free) RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MIC9131YM TR | 功能描述:电流型 PWM 控制器 SO-16 High Vin Telecom DC/DC PWM Control IC (Lead Free) RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MIC9131YQS | 功能描述:电流型 PWM 控制器 SO-16 High Vin Telecom DC/DC PWM Control IC (Lead Free) RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MIC9131YQS TR | 功能描述:电流型 PWM 控制器 SO-16 High Vin Telecom DC/DC PWM Control IC (Lead Free) RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。