- 您现在的位置：买卖IC网 > PDF目录18777 > MICRF011BM (Micrel Inc)IC RCVR/DATA DEMOD RF/IF 14SOIC PDF资料下载
参数资料
| 型号： | MICRF011BM |
| 厂商： | Micrel Inc |
| 文件页数： | 2/11页 |
| 文件大小： | 0K |
| 描述： | IC RCVR/DATA DEMOD RF/IF 14SOIC |
| 标准包装： | 54 |
| 频率： | 300MHz ~ 440MHz |
| 灵敏度： | -103dBm |
| 数据传输率 - 最大： | 10 kbps |
| 调制或协议： | OOK |
| 应用： | 车库门开启器 |
| 电流 - 接收： | 2.4mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 特点： | 自动调谐 |
| 电源电压： | 4.75 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOIC |
| 包装： | 管件 |
MICRF011
QwikRadio
tm
Micrel
Ordering Information
Part Number
MICRF011BN
MICRF011BM
Pin Configuration (DIP and SOIC)
Pin Description
Temperature Range
-40 ° C to +85 ° C
-40 ° C to +85 ° C
Package
14-Pin DIP
14-Pin SOIC
Pin Number
1
2/3
4
5
6
7
8
9/10
11
12
13
14
Pin Name
SEL0
VSSRF
ANT
VDDRF
VDDBB
CTH
DO
VSSBB
CAGC
SEL1
REFOSC
SWEN
Pin Function
Programs desired Demodulator Filter Bandwidth. This pin in internally pulled-up to VDD. See Table 1.
This pin is the ground return for the RF section of the IC. The bypass capacitor connected from VDDRF to
VSSRF should have the shortest possible lead length. For best performance, connect VSSRF to VSSBB
at the power supply only (i.e., keep VSSBB currents from flowing through VSSRF return path).
This is the receive RF input, internally ac-coupled. Connect this pin to the receive antenna. Input
impedance is high (FET gate) with approximately 2pF of shunt (parasitic) capacitance. For applications
located in high ambient noise environments, a fixed value band-pass network may be connected between
the ANT pin and VSSRF to provide additional receive selectivity and input overload protection. (See
“Application Note 22, MICRF001 Theory of Operation” .)
This pin is the positive supply input for the RF section of the IC. VDDBB and VDDRF should be connected
directly at the IC pins. Connect a low ESL, low ESR decoupling capacitor from this pin to VSSRF, as short
as possible.
This pin is the positive supply input for the baseband section of the IC. VDDBB and VDDRF should be
connected directly at the IC pins.
This capacitor extracts the (DC) average value from the demodulated waveform, which becomes the
reference for the internal data slicing comparator. Treat this as a low-pass RC filter with source impedance
of 118kohms (for REFOSC frequency ft=4.90MHz) . Note that variation in source resistance with filter
selection no longer exists, as it does for the MICRF001 . (See “Application Note 22, MICRF001 Theory
of Operation” , section 6.4). A standard ± 20% X7R ceramic capacitor is generally sufficient.
Output data pin. CMOS level compatible.
This is the ground return for the baseband section of the IC. The bypass and output capacitors connected
to VSSBB should have the shortest possible lead lengths. For best performance, connect VSSRF to
VSSBB at the power supply only (i.e., keep VSSBB currents from flowing through VSSRF return path).
Integrating capacitor for on-chip receive AGC (Automatic Gain Control). The Decay/Attack time-constant
(TC) ratio is nominally set as 10:1. Use of 0.47 μ F or greater is strongly recommended for best range
performance. See “Application Note 22, MICRF001 Theory of Operation” for further information.
Programs desired Demodulator Filter Bandwidth. This pin in internally pulled-up to VDD. See Table 1.
This is the timing reference for on-chip tuning and alignment. Connect either a ceramic resonator or crystal
(mode dependent) between this pin and VSSBB, or drive the input with an AC coupled 0.5Vpp input clock.
Use ceramic resonators without integral capacitors.
Note that if operated in FIXED mode, a crystal must be used; however in SWP mode, one may use either a
crystal or ceramic resonator. See “Application Note 22, MICRF001 Theory of Operation” for details on
frequency selection and accuracy.
This logic pin controls the operating mode of the MICRF011. When SWEN = HIGH, the MICRF011 is in
SWP mode. This is the normal (default) mode of the device. When SWEN = LOW, the device operates
as a conventional single-conversion superheterodyne receiver. (See “Application Note 22, MICRF001
Theory of Operation” for details.) This pin is internally pulled-up to VDD.
December 1998b
2
MICRF011
相关PDF资料 |
PDF描述 |
|---|---|
| AMB310908 | SENSOR REFL LONG H-TYPE |
| MICRF009BM | IC RECEIVER UHF LOW POWER 16SOIC |
| MICRF007BM | IC RECEIVER UHF LOW POWER 8SOIC |
| AMB345919 | SENSOR REFL LONG V TYPE W/OSC |
| MICRF001BN | IC RCVR/DATA DEMOD RF/IF 14DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MICRF011BM TR | 功能描述:IC RCVR/DATAMOD300-440MHZ 14SOIC RoHS:否 类别:RF/IF 和 RFID >> RF 接收器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS 产品变化通告:Product Discontinuation 09/Jan/2012 标准包装:50 系列:* 频率:850MHz ~ 2.175GHz 灵敏度:- 数据传输率 - 最大:- 调制或协议:- 应用:* 电流 - 接收:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 特点:- 电源电压:4.75 V ~ 5.25 V 工作温度:0°C ~ 85°C 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| MICRF011BN | 功能描述:IC RCVR/DATA DEMOD RF/IF 14DIP RoHS:否 类别:RF/IF 和 RFID >> RF 接收器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS 产品变化通告:Product Discontinuation 09/Jan/2012 标准包装:50 系列:* 频率:850MHz ~ 2.175GHz 灵敏度:- 数据传输率 - 最大:- 调制或协议:- 应用:* 电流 - 接收:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 特点:- 电源电压:4.75 V ~ 5.25 V 工作温度:0°C ~ 85°C 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| MICRF011YM | 功能描述:射频接收器 300-440MHz RF Receiver( Lead Free) RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel |
| MICRF011YM TR | 功能描述:射频接收器 300-440MHz RF Receiver( Lead Free) RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel |
| MICRF011YN | 功能描述:射频接收器 300-440MHz RF Receiver( Lead Free) RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。