- 您现在的位置：买卖IC网 > Datasheet目录477 > MICRF500BLQTR (Micrel Inc)TXRX UHF 700-1100MHZ 44-LQFP Datasheet资料下载
参数资料
| 型号： | MICRF500BLQTR |
| 厂商： | Micrel Inc |
| 文件页数： | 11/18页 |
| 文件大小： | 0K |
| 描述： | TXRX UHF 700-1100MHZ 44-LQFP |
| 标准包装： | 1,000 |
| 频率： | 700MHz 中心 |
| 数据传输率 - 最大： | 128kBaud |
| 调制或协议： | FSK |
| 应用： | 遥控，遥测 |
| 功率 - 输出： | 10dBm |
| 灵敏度： | -104dBm |
| 电源电压： | 2.5 V ~ 3.4 V |
| 电流 - 接收： | 12mA |
| 电流 - 传输： | 50mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 44-LQFP |
| 包装： | 带卷 (TR) |
MICRF500
The component values will be:
Micrel
through the Mod pin (Pin 11) which is a current output. The pin
IN
C115
1n
R101
C116
22n
R109
33k
C101
100p
OUT
sources a current of 50 μ A when Logic 1 is entered at the
DATAIXO and drains the current for Logic 0. The capacitance
of C17 will set the order of filtering of the baseband signal. A
large capacitance will give a slow ramp-up and therefore a
high order of filtering of the baseband signal, while a small
10k
Figure 5. Third Order Loop Filter
With this loop filter, internal modulation up to 2400bps is
possible. The PLL lock time from power-down to Rx will be
approximately 1ms.
Modulation Outside PLL (Closed Loop)
When modulation is applied outside the PLL, it means that the
PLL should not track the changes in the loop due to the
modulation signal. A loop filter with relatively low bandwidth
is therefore necessary. The exact bandwidth will depend on
the actual modulation rate. Because the loop bandwidth will
be significantly lower than the comparison frequency, a
second order loop filter will normally give adequate attenua-
capacitance gives a fast ramp-up, which in turn also gives a
broader frequency spectrum. Resistors R11 and R12 set the
frequency deviation. If C18 is large compared to C17, the
frequency deviation will be large. R13 should be large to
avoid influencing the loop filter. Pin DATAIXO must be kept
in tri-state from the time Tx-mode is entered until one starts
sending data.
Modulation Outside PLL, Dual-Loop Filters
Modulation outside the PLL requires a loop filter with a
relatively low bandwidth compared to the modulation rate.
This results in a relatively long loop lock time. In applications
where modulation is applied to the VCO, but at the same time
a short start-up time from power down to receive mode is
needed, dual-loop filters can be implemented. Figure 7
shows how to implement dual-loop filters.
tion of the comparison frequency. If not, a third order loop filter
may give the extra attenuation needed.
CMPOUT
Pin9
C16
C15
C116
C115
R102 33k
C103
R8 89k
towards_VCO
Example 2:
Radio frequency f RF
Comparison frequency f C
868MHz
140kHz
FLC
Pin10
68n
R10
10k
4.7n
R9
10k
1n
R109
10k
22n
100p
Loop bandwidth BW 900Hz
Pin4
VCO gain K o
Phase comparator gain K d
30MHz/V
125 μ A/rad
DFC
Phase margin j 61 °
Figure 7. Dual-Loop Filters
The component values will be:
IN
C16
68n
OUT
The loop filter used in transmit mode is made up of C15, C16,
R9 and R10. The fast lock feature is also included (internal
NMOS controlled by FLC, Fast Lock Control). This filter is
C15
4.7n
R9
10k
R10
10k
CmpR
automatically switched in/out by an internal NMOS at Pin 4,
QchOut, which is controlled by DFC (Dual Filter Control). Bits
OutS2, OutS1, OutS0 must be set to 110. When QchOut is
used to switch the Tx loop filter to ground, neither QchOut nor
Figure 6. Second Order Loop Filter
Data rates above approximately 19200baud (including
Manchester coding) can be used with this loop filter without
significant tracking of the modulating signal. PLL lock time will
be approximately 4ms.
If a faster PLL lock time is wanted, the charge pump can be
made to deliver a current of 500 μ A per unit phase error, while
an open drain NMOS on chip (Pin 10, CmpR) switches in a
second damping resistor (R10) to ground as shown in Figure
6. Once locked on the correct frequency, the PLL automati-
cally returns to standard low noise operation (charge pump
current: 125 μ A/rad). If correct settings have been made in the
control word (cpmp1 = 1, cpmp0 = 0), the fast locking feature
is activated and will reduce PLL lock time by a factor of two
without affecting the phase margin in the loop.
Components C17, C18 C19, R11, R12 and R13 (see applica-
tion circuit) are necessary if FSK modulation is applied to the
VCO. Data entered at the DATAIXO pin will then be fed
IchOut can be used as test pins to look at the different receiver
signals. The receive mode loop filter comprises C115, C116,
R109, R101 and C101.
Modulation Outside PLL (Open Loop)
In this mode the charge pump output is tri-stated. The loop is
open and will therefore not track the modulation. This means
that the loop filter can have a relatively high bandwidth, which
give short switching times. However, the loop voltage will
decrease with time due to current leakage. The transmit time
will therefore be limited and is dependent on the bandwidth of
the loop filter. High bandwidth gives low capacitor values and
the loop voltage will decrease faster, which gives a shorter
transmit time.
The loop is closed until the PLL is locked on the desired
frequency and the power amplifier is turned on. The loop
immediately opens when the modulation starts. The loop will
not track the modulation, but the modulation still needs to be
DC free due to the AC coupling in the modulation network.
March 2003
11
MICRF500
相关PDF资料 |
PDF描述 |
|---|---|
| MICRF501BLQ TR | TXRX SGL 300-600MHZ 44-LQFP |
| MICRF505DEV1 | KIT DEV RADIOWIRE 850-950MHZ |
| MICRF506DEV1 | EVAL BOARD EXPERIMENTAL MICRF506 |
| MICRF507YML TR | TXRX FSK LOW PWR W/AMP 32MLF |
| MICRF600DEV1 | KIT DEV RADIOWIRE 902-928MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MICRF500EVAL1 | 功能描述:射频开发工具 MICRF500 Evaluation Kit - For experimental use only RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MICRF501 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:300MHz to 600MHz RadioWire⑩ RF Transceiver |
| MICRF501BLQ | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:RF Micro Devices Inc 功能描述: |
| MICRF501BLQ TR | 功能描述:TXRX SGL 300-600MHZ 44-LQFP RoHS:否 类别:RF/IF 和 RFID >> RF 收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:30 系列:- 频率:4.9GHz ~ 5.9GHz 数据传输率 - 最大:54Mbps 调制或协议:* 应用:* 功率 - 输出:-3dBm 灵敏度:- 电源电压:2.7 V ~ 3.6 V 电流 - 接收:* 电流 - 传输:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 工作温度:-25°C ~ 85°C 封装/外壳:68-TQFN 裸露焊盘 包装:管件 |
| MICRF501EVAL1 | 功能描述:EVAL BOARD EXPERIMENTAL MICRF501 RoHS:否 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:RadioWire® 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796 |
发布紧急采购，3分钟左右您将得到回复。