- 您现在的位置：买卖IC网 > PDF目录9046 > MK1709SLF (IDT, Integrated Device Technology Inc)IC CLK GENERATOR LOW EMI 8-SOIC PDF资料下载
参数资料
| 型号： | MK1709SLF |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 4/9页 |
| 文件大小： | 0K |
| 描述： | IC CLK GENERATOR LOW EMI 8-SOIC |
| 标准包装： | 97 |
| 类型： | 时钟发生器 |
| PLL： | 是 |
| 输入： | 时钟 |
| 输出： | CMOS |
| 电路数： | 1 |
| 比率 - 输入:输出： | 1:1 |
| 差分 - 输入:输出： | 无/无 |
| 频率 - 最大： | 167MHz |
| 除法器/乘法器： | 无/无 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
MK1709
LOW EMI CLOCK GENERATOR
SSCG
IDT LOW EMI CLOCK GENERATOR
4
MK1709
REV M 051310
External Components
The MK1709 requires a minimum number of external
components for proper operation.
Decoupling Capacitor
A decoupling capacitor of 0.01F must be connected
between VDD and GND on pins 2 and 3 for the MK1709S,
or pins 1 and 8 for the MK1709AG. Place the capacitor as
close to these pins as possible. For optimum device
performance, the decoupling capacitor should be mounted
on the component side of the PCB. Avoid the use of vias in
the decoupling circuit.
Series Termination Resistor
When the PCB trace between the clock output and the load
is over 1 inch, series termination should be used. To series
terminate a 50
trace (a commonly used trace impedance),
place a 33
resistor in series with the clock line, as close to
the clock output pin as possible. The nominal impedance of
the clock output is 20
.
Select Pin Operation
The S1, S0 select pins are 2-level, meaning they have three
separate states to make the selections shown in the table on
page 2.
PCB layout Recommendations
For optimum device performance and lowest output phase
noise, the following guidelines should be observed.
1) The 0.01F decoupling capacitor should be mounted on
the component side of the board as close to the VDD pin as
possible. No vias should be used between the decoupling
capacitor and VDD pin. The PCB trace to VDD pin should
be kept as short as possible, as should the PCB trace to the
ground via.
2) Place a 33
series termination resistor (if needed) close
to the clock output to minimize EMI.
3) An optimum layout is one with all components on the
same side of the board, minimizing vias through other signal
layers. Other signal traces should be routed away from the
MK1709. This includes signal traces just underneath the
device, or on layers adjacent to the ground plane layer used
by the device.
相关PDF资料 |
PDF描述 |
|---|---|
| FSLV16211GX | IC SWITCH BUS 24BIT HS 54-FBGA |
| VE-JWN-MZ-F3 | CONVERTER MOD DC/DC 18.5V 25W |
| MS3122E22-55PW | CONN RCPT 55POS BOX MNT W/PINS |
| VE-JWN-MZ-F2 | CONVERTER MOD DC/DC 18.5V 25W |
| VE-JWN-MZ-F1 | CONVERTER MOD DC/DC 18.5V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MK1709SLFTR | 功能描述:时钟发生器及支持产品 LOW EMI CLOCK GENERATOR RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
| MK1709STR | 功能描述:IC CLK GENERATOR LOW EMI 8-SOIC RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:39 系列:- 类型:* PLL:带旁路 输入:时钟 输出:时钟 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 频率 - 最大:170MHz 除法器/乘法器:无/无 电源电压:2.375 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| MK171 | 制造商:Velleman Inc 功能描述:Voice Changer Kit |
| MK171101 | 制造商:ICS 制造商全称:ICS 功能描述:200 MHz Selectable Clock Source |
| MK1711-01 | 制造商:ICS 制造商全称:ICS 功能描述:200 MHz Selectable Clock Source |
发布紧急采购，3分钟左右您将得到回复。