- 您现在的位置：买卖IC网 > PDF目录80415 > MK20DX256ZVMB10 MICROCONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | MK20DX256ZVMB10 |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | MICROCONTROLLER, PQFP64 |
| 封装： | 12 X 12 MM, 1.70 MM HEIGHT, 0.65 MM PITCH, PLASTIC, LQFP-64 |
| 文件页数： | 20/84页 |
| 文件大小： | 3949K |
| 代理商： | MK20DX256ZVMB10 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页
MB95410H/470H Series
DS702-00004-1v0-E
27
■ NOTES ON DEVICE HANDLING
Preventing latch-ups
When using the device, ensure that the voltage applied does not exceed the maximum voltage rating.
In a CMOS IC, if a voltage higher than VCC or a voltage lower than VSS is applied to an input/output pin that
is neither a medium-withstand voltage pin nor a high-withstand voltage pin, or if a voltage out of the rating
range of power supply voltage mentioned in "1. Absolute Maximum Ratings" of “
When a latch-up occurs, power supply current increases significantly, which may cause a component to be
thermally destroyed.
Stabilizing supply voltage
Supply voltage must be stabilized.
A malfunction may occur when power supply voltage fluctuates rapidly even though the fluctuation is within
the guaranteed operating range of the VCC power supply voltage.
As a rule of voltage stabilization, suppress voltage fluctuation so that the fluctuation in VCC ripple (p-p value)
at the commercial frequency (50 Hz/60 Hz) does not exceed 10% of the standard VCC value, and the transient
fluctuation rate does not exceed 0.1 V/ms at a momentary fluctuation such as switching the power supply.
Notes on using the external clock
When an external clock is used, oscillation stabilization wait time is required for power-on reset, wake-up
from subclock mode or stop mode.
■ PIN CONNECTION
Treatment of unused input pins
If an unused input pin is left unconnected, a component may be permanently damaged due to malfunctions
or latch-ups. Always pull up or pull down an unused input pin through a resistor of at least 2 k
Ω. Set an
unused input/output pin to the output state and leave it unconnected, or set it to the input state and treat it
the same as an unused input pin. If there is an unused output pin, leave it unconnected.
Power supply pins
To reduce unnecessary electro-magnetic emission, prevent malfunctions of strobe signals due to an increase
in the ground level, and conform to the total output current standard, always connect the VCC pin and the VSS
pin to the power supply and ground outside the device. In addition, connect the current supply source to the
VCC pin and the VSS pin with low impedance.
It is also advisable to connect a ceramic capacitor of approximately 0.1 F as a bypass capacitor between
the VCC pin and the VSS pin at a location close to this device.
DBG pin
Connect the DBG pin directly to an external pull-up resistor.
To prevent the device from unintentionally entering the debug mode due to noise, minimize the distance
between the DBG pin and the VCC or VSS pin when designing the layout of the printed circuit board.
The DBG pin should not stay at “L” level after power-on until the reset output is released.
RST pin
Connect the RST pin directly to an external pull-up resistor.
To prevent the device from unintentionally entering the reset mode due to noise, minimize the distance
between the RST pin and the VCC or VSS pin when designing the layout of the printed circuit board.
The PF2/RST pin functions as the reset input/output pin after power-on. In addition, the reset output function
of the PF2/RST pin can be enabled by the RSTOE bit in the SYSC register, and the reset input function or
the general purpose I/O function can be selected by the RSTEN bit in the SYSC register.
Analog power supply
Always set the same potential to AVCC and VCC pins. When VCC is larger than AVCC, the current may flow
through the AN00 to AN07 pins.
相关PDF资料 |
PDF描述 |
|---|---|
| MK52DN512ZCMD10R | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PBGA144 |
| MK53DN512ZCLQ10R | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP144 |
| MPC8360CZUAGFHA | 32-BIT, 400 MHz, RISC PROCESSOR, PBGA740 |
| MPC8280VVIX | 32-BIT, 200 MHz, RISC PROCESSOR, PBGA480 |
| MPC8280ZQMX | 32-BIT, 266 MHz, RISC PROCESSOR, PBGA516 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MK20DX256ZVMC10 | 制造商:Freescale Semiconductor 功能描述:MCU 32-bit K20 ARM Cortex M4 RISC 256KB Flash 1.8V/2.5V/3.3V 121-Pin MAP-BGA Tray 制造商:Freescale Semiconductor 功能描述:MK20DX256ZVMC10 - Bulk 制造商:Freescale Semiconductor 功能描述:IC ARM CORTEX MCU 256KB 121BGA 制造商:Freescale Semiconductor 功能描述:MCU KINETIS K20 CORTEX M4 制造商:Freescale Semiconductor 功能描述:MCU, KINETIS, K20, CORTEX M4, 121MAP 制造商:Freescale Semiconductor 功能描述:KINETIS 256K USB 制造商:Freescale Semiconductor 功能描述:IC 32BIT MCU KINETIS K20 100MHZ 121-MAPBGA; Controller Family/Series:(ARM Cortex - M4) Kinetis K20; Core Size:32bit; No. of I/O's:86; Supply Voltage Min:1.71V; Supply Voltage Max:3.6V; Digital IC Case Style:MAPBGA; No. of Pins:121 ;RoHS Compliant: Yes |
| MK20DX256ZVMD10 | 功能描述:ARM微控制器 - MCU KINETIS CORTEX M4 256KFLEX USB RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| MK20DX32VFM5 | 功能描述:ARM微控制器 - MCU Kinetis 32K Flex RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| MK20DX32VFT5 | 功能描述:ARM微控制器 - MCU Kinetis 32K Flex RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| MK20DX32VLF5 | 功能描述:ARM微控制器 - MCU Kinetis 32K Flex RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。