参数资料
型号: MK2727S
元件分类: 时钟产生/分配
英文描述: 27 MHz, OTHER CLOCK GENERATOR, PDSO8
封装: 0.150 INCH, SOIC-8
文件页数: 3/6页
文件大小: 125K
代理商: MK2727S
LOW COST 27 MHZ VCXO
MDS 2727 C
3
Revision 040704
In te gr ated Circuit Systems
525 Race Stree t , Sa n Jose, CA 9 512 6
tel (4 08) 2 97-12 01
www.icst.com
MK2727
External Component Selection
The MK2727 requires a minimum number of external
components for proper operation.
Decoupling Capacitor
A decoupling capacitor of 0.01F must be connected
between VDD (pin 2) and GND (pin 4), as close to
these pins as possible. For optimum device
performance, the decoupling capacitor should be
mounted on the component side of the PCB. Avoid the
use of vias in the decoupling circuit.
Series Termination Resistor
When the PCB trace between the clock output (CLK,
pin 5) and the load is over 1 inch, series termination
should be used. To series terminate a 50
trace (a
commonly used trace impedance), place a 33
resistor
in series with the clock line, as close to the clock output
pin as possible. The nominal impedance of the clock
output is 20
.
Quartz Crystal
The MK2727 VCXO function consists of the external
crystal and the integrated VCXO oscillator circuit. To
assure the best system performance (frequency pull
range) and reliability, a crystal device with the
recommended parameters (shown below) must be
used, and the layout guidelines discussed in the
following section shown must be followed.
The frequency of oscillation of a quartz crystal is
determined by its “cut” and by the load capacitors
connected to it. The MK2727 incorporates on-chip
variable load capacitors that “pull” (change) the
frequency of the crystal. The crystal specified for use
with the MK2727 is designed to have zero frequency
error when the total of on-chip + stray capacitance is
14 pF.
Recommended Crystal Parameters:
Initial Accuracy at 25°C±20 ppm
Temperature Stability
±30 ppm
Aging
±20 ppm
Load Capacitance
14 pf
Shunt Capacitance, C0
7 pF Max
C0/C1 Ratio
250 Max
Equivalent Series Resistance
35
Max
The external crystal must be connected as close to the
chip as possible and should be on the same side of the
PCB as the MK2727. There should be no vias between
the crystal pins and the X1 and X2 device pins. There
should be no signal traces underneath or close to the
crystal.
Crystal Tuning Load Capacitors
The crystal traces should include pads for small fixed
capacitors, one between X1 and ground, and another
between X2 and ground. The need for these capacitors
is determined at system prototype evaluation, and is
influenced by the particular crystal used (manufacture
and frequency) and by PCB layout. The typical required
capacitor value is 1 to 4 pF.
相关PDF资料
PDF描述
MK3754S 54 MHz, OTHER CLOCK GENERATOR, PDSO8
MK2742-06S 81 MHz, VIDEO CLOCK GENERATOR, PDSO16
MK2715-01STR 17.7345 MHz, VIDEO CLOCK GENERATOR, PDSO16
MB90523PFF-G 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP120
M48T35Y-70MH6 0 TIMER(S), REAL TIME CLOCK, PDSO28
相关代理商/技术参数
参数描述
MK2727SLF 功能描述:IC VCXO/PLL CLK SYNTHESIZR 8SOIC RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器,PLL,频率合成器 系列:- 标准包装:2,000 系列:- 类型:PLL 时钟发生器 PLL:带旁路 输入:LVCMOS,LVPECL 输出:LVCMOS 电路数:1 比率 - 输入:输出:2:11 差分 - 输入:输出:是/无 频率 - 最大:240MHz 除法器/乘法器:是/无 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-LQFP 供应商设备封装:32-TQFP(7x7) 包装:带卷 (TR)
MK2727SLFTR 功能描述:IC VCXO/PLL CLK SYNTHESIZR 8SOIC RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器,PLL,频率合成器 系列:- 标准包装:2,000 系列:- 类型:PLL 时钟发生器 PLL:带旁路 输入:LVCMOS,LVPECL 输出:LVCMOS 电路数:1 比率 - 输入:输出:2:11 差分 - 输入:输出:是/无 频率 - 最大:240MHz 除法器/乘法器:是/无 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-LQFP 供应商设备封装:32-TQFP(7x7) 包装:带卷 (TR)
MK2727STR 功能描述:IC VCXO/PLL CLK SYNTHESIZR 8SOIC RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器,PLL,频率合成器 系列:- 标准包装:39 系列:- 类型:* PLL:带旁路 输入:时钟 输出:时钟 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 频率 - 最大:170MHz 除法器/乘法器:无/无 电源电压:2.375 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:*
MK2731-03C 制造商:ICS 制造商全称:ICS 功能描述:MPEG Audio Clock Synthesizer
MK2731-03S 制造商:ICS 制造商全称:ICS 功能描述:MPEG Audio Clock Synthesizer