参数资料
型号: MK52N512CMD100
厂商: FREESCALE SEMICONDUCTOR INC
元件分类: 微控制器/微处理器
英文描述: 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PBGA144
封装: 13 X 13 MM, MAPBGA-144
文件页数: 20/75页
文件大小: 1832K
代理商: MK52N512CMD100
Table 13. MCG specifications (continued)
Symbol
Description
Min.
Typ.
Max.
Unit
Notes
Dlock
Lock entry frequency tolerance
± 1.49
± 2.98
%
Dunl
Lock exit frequency tolerance
± 4.47
± 5.97
%
tpll_lock
Lock detector detection time
0.15 +
1075(1/
fpll_ref)
ms
1. This parameter is measured with the internal reference (slow clock) being used as a reference to the FLL (FEI clock
mode).
2. These typical values listed are with the slow internal reference clock (FEI) using factory trim and DMX32=0.
3. The resulting system clock frequencies should not exceed their maximum specified values. The DCO frequency deviation
(
Δfdco_t) over voltage and temperature should be considered.
4. These typical values listed are with the slow internal reference clock (FEI) using factory trim and DMX32=1.
5. The resulting clock frequency must not exceed the maximum specified clock frequency of the device.
6. This specification was obtained at TBD frequency.
7. This specification applies to any time the FLL reference source or reference divider is changed, trim value is changed,
DMX32 bit is changed, DRS bits are changed, or changing from FLL disabled (BLPE, BLPI) to FLL enabled (FEI, FEE,
FBE, FBI). If a crystal/resonator is being used as the reference, this specification assumes it is already running.
8. Excludes any oscillator currents that are also consuming power while PLL is in operation.
9. This specification was obtained using a Freescale developed PCB. PLL jitter is dependent on the noise characteristics of
each PCB and results will vary.
10. This specification was obtained at internal frequency of TBD.
11. This specification applies to any time the PLL VCO divider or reference divider is changed, or changing from PLL disabled
(BLPE, BLPI) to PLL enabled (PBE, PEE). If a crystal/resonator is being used as the reference, this specification assumes
it is already running.
6.3.2 Oscillator electrical specifications
This section provides the electrical characteristics of the module.
6.3.2.1 Oscillator DC electrical specifications
Table 14. Oscillator DC electrical specifications
Symbol
Description
Min.
Typ.
Max.
Unit
Notes
VDD
Supply voltage
1.71
3.6
V
IDDOSC
Supply current — low-power mode (HGO=0)
32 kHz
4 MHz
8 MHz
16 MHz
24 MHz
32 MHz
500
200
300
700
1.2
1.5
nA
μA
mA
Table continues on the next page...
Peripheral operating requirements and behaviors
K52 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011.
Freescale Semiconductor, Inc.
Preliminary
27
相关PDF资料
PDF描述
MK52N512CLQ100R 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP144
ML2037IP 1-BIT, DSP-NUM CONTROLLED OSCILLATOR, PDIP16
ML2037CP 1-BIT, DSP-NUM CONTROLLED OSCILLATOR, PDIP16
ML2037IS 1-BIT, DSP-NUM CONTROLLED OSCILLATOR, PDSO16
ML53101 1 CHANNEL(S), 100M bps, LOCAL AREA NETWORK CONTROLLER, PBGA352
相关代理商/技术参数
参数描述
MK531BZ 制造商:BROTHER 功能描述:12MM BLACK ON BLUE
MK53731 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:SINGLE NUMBER PULSE TONE SWITCHABLE DIALER
MK53732 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:TONE PULSE DIALER WITH LAST NUMBER AND SAVE FUNCTION
MK53732A 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:TONE PULSE DIALER WITH LAST NUMBER AND SAVE FUNCTION
MK53732AD 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:TONE PULSE DIALER WITH LAST NUMBER AND SAVE FUNCTION