- 您现在的位置：买卖IC网 > PDF目录80443 > ML9040A-A01GA (OKI ELECTRIC INDUSTRY CO LTD) 16 X 40 DOTS DOT MAT LCD DRVR AND DSPL CTLR, PQFP80 PDF资料下载
参数资料
| 型号： | ML9040A-A01GA |
| 厂商： | OKI ELECTRIC INDUSTRY CO LTD |
| 元件分类： | 显示控制器 |
| 英文描述： | 16 X 40 DOTS DOT MAT LCD DRVR AND DSPL CTLR, PQFP80 |
| 封装： | 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件页数： | 27/49页 |
| 文件大小： | 515K |
| 代理商： | ML9040A-A01GA |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
ML9040A-Axx/-Bxx
Semiconductor
33/49
PEDL9040A-03
Interface with LCD and MSM5259
Display examples when setting the 5 x 7 dots character font 1-line mode, 5 x 10 dots character font
1-line mode, and 5 x 7 dots character font 2-line mode through instructions are shown in Figures
4, 5, and 6, respectively.
When the 5 x 7 dots character font is set in the 1-line display mode, the COM signals COM9 to
COM16 are output for extinguishing.
Likewise, when the 5 x 10 dots character font (1-line is set), the COM signals COM12 to COM16
are output for display-off.
The display example shows a combination of 16 characters (32 characters for the 2-line display
mode) and the LCD. When the number of MSM5259s are increased according to the increase in
the number of characters, it is possible to display a maximum of 80 characters.
Besides, it is necessary to generate bias voltage required for LCD operation by splitting resistors
outside the IC to input it to ML9040A-Axx/-Bxx and MSM5259.
Examples of these bias voltages are shown in Figures 7, 8, 9, and 10. Basically, this can be done
by dividing the voltage by the resistors as shown in Figures 7 and 8. If the value of resistor R is
made larger to reduce system power consumption, the LCD operating margin decreases and the
LCD driving waveform is distorted. To prevent this, a by-pass capacitor is serially connected to
the resistor to lower voltage division impedance caused by the splitting of resistors as shown in
Figures 9 and 10.
As the values of R, VR, and C vary according to the LCD size used and VLCD (LCD drive voltage),
these values have to be determined through actual experimentation in combination with the
LCD.
(Example set values: R = 3.3 to 10kW, VR = 10 to 30kW, and C = 0.0022 mF to 0.047 mF)
Figure 17 shows an application circuit for the ML9040A-Axx/-Bxx and MSM5259 including a
bias circuit.
The bias voltage has to maintain the following potential relation:
VDD > V1 > V2 ≥ V3 > V4 > V5
Figure 4
In the case of 1-line 16 characters display (5 x 7 dots/font)
COM1
SEG1
SEG40
O1
O40
DO
CP
DF
L
DI1
CP
MSM5259
DF
LOAD
DO20 DI21
LCD
COM8
ML9040A-Axx/-Bxx
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC908AS60AMFU | 8-BIT, FLASH, 8.4 MHz, MICROCONTROLLER, PQFP64 |
| MC68HC05C8AMP | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP40 |
| MC68HC11N4CFU3 | 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQFP80 |
| MC68HC711N4VFE2 | 8-BIT, UVPROM, 2 MHz, MICROCONTROLLER, CQFP80 |
| MC68HC05PV8AYDWR2 | 8-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PDSO28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ML9040A-A01GAZ03A-7 | 功能描述:LCD 驱动器 LCD DOT Matrix Controller, 16/40 RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| ML9040A-A01GAZ0A-ML | 制造商:ROHM Semiconductor 功能描述: |
| ML9040A-AXX | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:DOT MATRIX LCD CONTROLLER WITH 16-DOT COMMON DRIVER AND 40-DOT SEGMENT DRIVER |
| ML9040A-B01GAZ03A-7 | 功能描述:LCD 驱动器 LCD DOT Matrix Controller, 16/40 RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| ML9040A-BXX | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:DOT MATRIX LCD CONTROLLER WITH 16-DOT COMMON DRIVER AND 40-DOT SEGMENT DRIVER |
发布紧急采购，3分钟左右您将得到回复。