- 您现在的位置：买卖IC网 > PDF目录69035 > ML9208-01MB (OKI ELECTRIC INDUSTRY CO LTD) 16 X 35 DOTS DOT MAT LCD DRVR AND DSPL CTLR, PDSO64 PDF资料下载
参数资料
| 型号： | ML9208-01MB |
| 厂商： | OKI ELECTRIC INDUSTRY CO LTD |
| 元件分类： | 显示控制器 |
| 英文描述： | 16 X 35 DOTS DOT MAT LCD DRVR AND DSPL CTLR, PDSO64 |
| 封装： | 0.525 INCH, 0.80 MM PITCH, PLASTIC, SSOP-64 |
| 文件页数： | 6/33页 |
| 文件大小： | 337K |
| 代理商： | ML9208-01MB |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
FEDL9208-01
OKI Semiconductor
ML9208
14/33
Data Transfer Method and Command Write Method
Display control command and data are written by an 8-bit serial transfer.
Write timing is shown in the figure below.
Setting the
CS pin to “Low” level enables a data transfer.
Data is 8 bits and is sequentially input into the DA pin from LSB (LSB first).
As shown in the figure below, data is read by the shift register at the rising edge of the shift clock, which is input
into the
CP pin. If 8-bit data is input, internal load signals are automatically generated and data is written to each
register and RAM.
Therefore it is not necessary to input load signals from the outside.
Setting the
CS pin to “High” disables data transfer. Data input from the point when the CS pin changes from
“High” to “Low” is recognized in 8-bit units.
tDOFF
B0
LSB
CS
CP
DA
B1B2B3B4B5B6B7
B0B1B2B3B4B5B6B7
MSB
1st byte
LSB
MSB
2nd byte
When data is written
to DCRAM*
Command and address
data
tCSH
B0B1B2B3B4B5B6B7
LSB
MSB
2nd byte
Character code data of
the next address
Character code data
*
When data is written to RAM (DCRAM, ADRAM, CGRAM) continuously, addresses are internally
incremented automatically.
Therefore it is not necessary to specify the 1st byte to write RAM data for the 2nd and later bytes.
Reset Function
Reset is executed when the
RESET pin is set to “L”, (when turning power on, for example) and initializes all
functions.
Initial status is as follows.
Address of each RAM address “00”H
Data of each RAM All contents are undefined
General output port All general output ports go “Low”
Display digit 16 digits
Contrast adjustment 8/16
All display lights ON or OFF OFF mode
Segment output All segment outputs go “Low”
AD output All AD outputs go “Low”
Please set again according to “Setting Flowchart” after reset.
相关PDF资料 |
PDF描述 |
|---|---|
| ML9208-01GA | 16 X 35 DOTS DOT MAT LCD DRVR AND DSPL CTLR, PQFP64 |
| MLX90314AALLW | MICROCONTROLLER, PDSO16 |
| MLX90314AALUD | MICROCONTROLLER, UUC |
| MM908E625ACPEK | FLASH, 32 MHz, MICROCONTROLLER, PDSO54 |
| MM908E630CVFC | MICROCONTROLLER, QCC44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ML9208-XX | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:5 X 7 Dot Character X 16-Digit Display Controller/Driver with Character RAM |
| ML9208-XXGA | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:5 X 7 Dot Character X 16-Digit Display Controller/Driver with Character RAM |
| ML9208-XXMB | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:5 X 7 Dot Character X 16-Digit Display Controller/Driver with Character RAM |
| ML9209 | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:Vacuum fluorescent display tube controller driver |
| ML9209-01 | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:Vacuum fluorescent display tube controller driver |
发布紧急采购，3分钟左右您将得到回复。