- 您现在的位置：买卖IC网 > PDF目录382336 > MM74HC942J (NATIONAL SEMICONDUCTOR CORP) MM74HC942 is a full duplex low speed modem PDF资料下载
参数资料
| 型号： | MM74HC942J |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 调制器/解调器 |
| 英文描述： | MM74HC942 is a full duplex low speed modem |
| 中文描述： | 0.3 kbps DATA, MODEM, CDIP20 |
| 封装： | DIP-20 |
| 文件页数： | 5/8页 |
| 文件大小： | 146K |
| 代理商： | MM74HC942J |
Functional Description
(Continued)
THE DEMODULATOR SECTION
The Receive Filter
The demodulator recovers the data from the received sig-
nals. The signal from the hybrid is a mixture of transmitted
signal, received signals and noise. The first stage of the
receive filter is an anti-alias filter which attenuates high fre-
quency noise before sampling occurs. The signal then goes
to the second stage of the receive filter where the transmit-
ted tones and other noise are filtered from the received sig-
nal. This is a switched capacitor nine-pole filter providing at
least 60 dB of transmitted tone rejection. This also provides
high attenuation at 60 Hz, a common noise component.
The Discriminator
The first stage of the discriminator is a hard limiter. The hard
limiter removes from the received signal any amplitude
modulation which may bias the demodulator toward a mark
or a space. It compares the output of the receive filter to the
voltage on the 0.1
m
F capacitor on the FTLC pin.
The hard limiter output connects to two parallel bandpass
filters in the discriminator. One filter is tuned to the mark
frequency and the other to the space frequency. The out-
puts of these filters are rectified, filtered and compared. If
the output of the mark path exceeds the output of the space
path the RXD output goes high. The opposite case sends
RXD low.
The demodulator is implemented using precision switched
capacitor techniques. The highly critical comparators in the
limiter and discriminator are auto-zeroed for low offset.
Carrier Detector
The output of the discriminator is meaningful only if there is
sufficient carrier being received. This is established in the
carrier detection circuit which measures the signal on the
line. If this exceeds a certain level for a preset period (ad-
justable by the CDT pin) the CD output goes low indicating
that carrier is present. Then the carrier detect threshold is
lowered by 3 dB. This provides hysteresis ensuring the CD
output remains stable. If carrier is lost CD goes high after
the preset delay and the threshold is increased by 3 dB.
MODULATOR SECTION
The modulator consists of a frequency synthesizer and a
sine wave synthesizer. The frequency produces one of four
tones depending on the O/A and TXD pins. The frequencies
are synthesized to high precision using a crystal oscillator
and variable dual modulus counter. The counters used re-
spond quickly to data changes, introducing negligible bit jit-
ter while maintaining phase coherence.
The sine wave synthesizer uses switched capacitors to
‘‘look up’’ the voltages of the sine wave. This sampled sig-
nal is then further processed by switched capacitor and
continuous filters to ensure the high spectral purity required
by FCC regulations.
Applications Information
TRANSMIT LEVEL ADJUSTMENT
The transmitted power levels of Table II refer to the power
delivered to a 600
X
load from the external 600
X
source
impedance. The voltage on the load is half the TXA voltage.
This should be kept in mind when designing interface cir-
cuits which do not match the load and source impedances.
The transmit level is programmable by placing a resistor
from TLA to VCC. With a 5.5k resistor the line driver trans-
mits a maximum of
b
9 dBm. Since most lines from a phone
installation to the exchange provide 3 dB of attenuation the
maximum level reaching the exchange will be
b
12 dBm.
This is the maximum level permitted by most telephone
companies. Thus with this programming the MM74HC942
will interface to most telephones. This arrangement is called
the ‘‘permissive arrangement.’’ The disadvantage with the
permissive arrangement is that when the loss from a phone
to the exchange exceeds 3 dB, no compensation is made
and SNR may be unnecessarily degraded.
SNR can be maximized by adjusting the transmit level until
the level at the exchange reaches
b
12 dBm. This must be
done with the cooperation of the telephone company. The
programming resistor used is specific for a given installation
and is often included in the telephone jack at the installa-
tion. The modem is thus programmable and can be used
with any jack correctly wired. This arrangement is called the
universal registered jack arrangement and is possible with
the MM74HC942. The values of resistors required to pro-
gram the MM74HC942 follow the most common code in
use; the universal service order code. The required resistors
are given in Table II.
TABLE II. Universal Service Order Code Resistor Values
Line
Loss
(dB)
Transmit
Level
(dBm)
Programming
Resistor (R
TLA
)
(Ohms)
0
1
2
3
4
5
6
7
8
9
10
11
12
b
12
b
11
b
10
b
9
b
8
b
7
b
6
b
5
b
4
b
3
b
2
b
1
Open
19,800
9,200
5,490
3,610
2,520
1,780
1,240
866
562
336
150
0
0
CARRIER DETECT THRESHOLD ADJUSTMENT
The carrier detect threshold is directly proportional to the
voltage on CDA. This pin is connected internally to a high
impedance source. This source has a nominal Thevenin
equivalent voltage of 1.2V and output impedance of 100 k
X
.
By forcing the voltage on CDA the carrier detect threshold
may be adjusted. To find the voltage required for a given
threshold the following equation may be used;
V
CDA
e
244
c
V
ON
V
CDA
e
345
c
V
OFF
CARRIER DETECT TIMING ADJUSTMENT
CDT: A capacitor on Pin 4 sets the time interval that the
carrier must be present before CD goes low. It also
sets the time interval that carrier must be removed
before CD returns high. The relevant timing equations
are:
T
CDL
j
6.4
c
C
CDT
for CD going low
T
CDH
j
0.54
c
C
CDT
for CD going high
Where T
CDL
& T
CDH
are in seconds, and C
CDT
is in
m
F.
5
相关PDF资料 |
PDF描述 |
|---|---|
| MM74HC942N | MM74HC942 is a full duplex low speed modem |
| MM74HC943 | Low-Voltage Adjustable Precision Shunt Regulator 3-TO-92 -40 to 85 |
| MM74HC943J | Low-Voltage Adjustable Precision Shunt Regulator 3-TO-92 -40 to 85 |
| MM74HC943N | Low-Voltage Adjustable Precision Shunt Regulator 3-SOT-89 -40 to 85 |
| MM74HCT109 | ANA 5V USR DFINED LIN REG; Package: SO-16 WB; No of Pins: 16; Container: Tape and Reel; Qty per Container: 1000 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MM74HC942N | 制造商:NSC 制造商全称:National Semiconductor 功能描述:MM74HC942 is a full duplex low speed modem |
| MM74HC943 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:300 Baud Modem |
| MM74HC943J | 制造商:NSC 制造商全称:National Semiconductor 功能描述:300 Baud Modem |
| MM74HC943N | 制造商:NSC 制造商全称:National Semiconductor 功能描述:300 Baud Modem |
| MM74HCA393M | 制造商:Texas Instruments 功能描述: |
发布紧急采购，3分钟左右您将得到回复。