参数资料
型号: MM908E626AVDWB
厂商: Freescale Semiconductor
文件页数: 21/43页
文件大小: 0K
描述: IC STEPPER MOTOR DRIVER 54-SOIC
标准包装: 26
应用: 自动镜像控制
核心处理器: HC08
程序存储器类型: 闪存(16 kB)
控制器系列: 908E
RAM 容量: 512 x 8
接口: SCI,SPI
输入/输出数: 13
电源电压: 8 V ~ 18 V
工作温度: -40°C ~ 115°C
安装类型: 表面贴装
封装/外壳: 54-BSSOP(0.295",7.50mm 宽)裸露焊盘
包装: 管件
供应商设备封装: 54-SOICW-EP
Analog Integrated Circuit Device Data
28
Freescale Semiconductor
908E626
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Figure 15. BEMF Signal Generation
HALF-BRIDGE OVERTEMPERATURE
PROTECTION
The half-bridge outputs provide an overtemperature
prewarning with the HTF in the Interrupt Flag Register (IFR).
In order to protect the outputs against overtemperature, the
High Temperature Reset must be enabled. If this value is
reached, the part generates a reset and disables all power
outputs.
HALF-BRIDGE OVERCURRENT PROTECTION
The half-bridges are protected against short to GND, short
to VSUP, and load shorts.
In the event an overcurrent on the high side is detected,
the high side MOSFETs on all HB high side MOSFETs are
switched off automatically. In the event an overcurrent on the
low side is detected, all HB low side MOSFETs are switched
off automatically. In both cases, the overcurrent status flag
HB_OCF in the System Status Register (SYSSTAT) is set.
The overcurrent status flag is cleared (and the outputs re-
enabled) by writing a logic [1] to the HB_OCF flag in the
System Status Register or by reset.
HALF-BRIDGE OVERVOLTAGE/UNDERVOLTAGE
The half-bridge outputs are protected against
undervoltage and overvoltage conditions. This protection is
done by the low and high voltage interrupt circuitry. If one of
these flags (LVF, HVF) is set, the outputs are automatically
disabled.
The overvoltage/undervoltage status flags are cleared
(and the outputs re-enabled) by writing a logic [1] to the LVF/
HVF flags in the Interrupt Flag Register or by reset. Clearing
this flag is useless as long as a high or low voltage condition
is present.
Half-bridge Control Register (HBCTL)
OFC_EN—H-bridge Offset Chopping Enable Bit
This read/write bit enables offset chopping. Reset clears
the OFC_EN bit.
1 = Offset chopping enabled.
0 = Offset chopping disabled.
CSA—H-bridges Current Sense Amplification Select Bit
This read/write bit selects the current sense amplification
of the H-bridges. Reset clears the CSA bit.
Coil Current
Voltage on
1
BEMF Signal
Register Name and Address: HBCTL - $02
Bit7
6
5
4
3
2
1
Bit0
Read
OFC_EN
CSA
0
CLS2 CLS1 CLS0
Write
Reset
0
相关PDF资料
PDF描述
MM912F634BV1AER2 IC MCU 16BIT 32KB FLASH 48LQFP
MM912H634CM1AER2 IC 64KS12 LIN2XLS/HS ISENSE
MMC2001HCAB33B IC MCU 32BIT 33MHZ 144-LQFP
MMC2107CFCPU33 IC MCU 32BIT 33MHZ 100-LQFP
MMC2114CFCAG33 IC MCU 32BIT 33MHZ 144-LQFP
相关代理商/技术参数
参数描述
MM908E626AVDWB/R2 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
MM908E626AVEK 功能描述:马达/运动/点火控制器和驱动器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MM908E626AVPEK 功能描述:8位微控制器 -MCU MCU + LIN + MOTOR DRIVER RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
MM908E626AVPEKR2 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
MM908E626R2 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication