- 您现在的位置：买卖IC网 > PDF目录378673 > MMFT107T1D (ON SEMICONDUCTOR) Power MOSFET 250 mA, 200 Volts PDF资料下载
参数资料
| 型号： | MMFT107T1D |
| 厂商： | ON SEMICONDUCTOR |
| 英文描述： | Power MOSFET 250 mA, 200 Volts |
| 中文描述： | 功率MOSFET二百五十○毫安，200伏特 |
| 文件页数： | 5/6页 |
| 文件大小： | 118K |
| 代理商： | MMFT107T1D |
5
Motorola Small–Signal Transistors, FETs and Diodes Device Data
SOLDER STENCIL GUIDELINES
Prior to placing surface mount components onto a printed
circuit board, solder paste must be applied to the pads. A
solder stencil is required to screen the optimum amount of
solder paste onto the footprint. The stencil is made of brass
or stainless steel with a typical thickness of 0.008 inches.
The stencil opening size for the SOT-223 package should be
the same as the pad size on the printed circuit board, i.e., a
1:1 registration.
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100
°
C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference should be a maximum of 10
°
C.
The soldering temperature and time should not exceed
260
°
C for more than 10 seconds.
When shifting from preheating to soldering, the
maximum temperature gradient should be 5
°
C or less.
After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and result
in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied during
cooling
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of control
settings that will give the desired heat pattern. The operator
must set temperatures for several heating zones, and a
figure for belt speed. Taken together, these control settings
make up a heating “profile” for that particular circuit board.
On machines controlled by a computer, the computer
remembers these profiles from one operating session to the
next. Figure 10 shows a typical heating profile for use when
soldering a surface mount device to a printed circuit board.
This profile will vary among soldering systems but it is a good
starting point. Factors that can affect the profile include the
type of soldering system in use, density and types of
components on the board, type of solder used, and the type
of board or substrate material being used. This profile shows
temperature versus time. The line on the graph shows the
actual temperature that might be experienced on the surface
of a test board at or near a central solder joint. The two
profiles are based on a high density and a low density board.
The Vitronics SMD310 convection/infrared reflow soldering
system was used to generate this profile. The type of solder
used was 62/36/2 Tin Lead Silver with a melting point
between 177–189
°
C. When this type of furnace is used for
solder reflow work, the circuit boards and solder joints tend to
heat first. The components on the board are then heated by
conduction. The circuit board, because it has a large surface
area, absorbs the thermal energy more efficiently, then
distributes this energy to the components. Because of this
effect, the main body of a component may be up to 30
degrees cooler than the adjacent solder joints.
STEP 1
PREHEAT
ZONE 1
“RAMP”
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
STEP 2
VENT
“SOAK”
STEP 3
HEATING
ZONES 2 & 5
“RAMP”
STEP 4
HEATING
ZONES 3 & 6
“SOAK”
STEP 5
HEATING
ZONES 4 & 7
“SPIKE”
170
°
C
STEP 6
VENT
STEP 7
COOLING
200
°
C
150
°
C
100
°
C
50
°
C
TIME (3 TO 7 MINUTES TOTAL)
Figure 10. Typical Solder Heating Profile
TMAX
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
MASS OF ASSEMBLY)
205
°
TO
219
°
C
PEAK AT
SOLDER
JOINT
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
100
°
C
150
°
C
160
°
C
140
°
C
相关PDF资料 |
PDF描述 |
|---|---|
| MMFT107T3 | Power MOSFET 250 mA, 200 Volts |
| MMFT108T1 | TMOS FET TRANSISTOR N-CHANNEL - ENHANCEMENT |
| MMFT2406T1 | MEDIUM POWER TMOS FET 700 mA 240 VOLTS |
| MMFT2406T | MEDIUM POWER TMOS FET 700 mA 240 VOLTS |
| MMFT2955E | TMOS MEDIUM POWER FET 1.2 AMP 60 VOLTS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MMFT107T3 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Power MOSFET 250 mA, 200 Volts |
| MMFT108T1 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:TMOS FET TRANSISTOR N-CHANNEL - ENHANCEMENT |
| MMFT1N10 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:MEDIUM POWER TMOS FET 1 AMP 100 VOLTS |
| MMFT1N10E | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:MEDIUM POWER TMOS FET 1 AMP 100 VOLTS |
| MMFT1N10ET1 | 制造商:ON Semiconductor 功能描述:Trans MOSFET N-CH 100V 1A 4-Pin(3+Tab) SOT-223 T/R 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。