MAD00006HEM
MN101C28 Series
Type
MN101C28A MN101C28C MN101C28D MN101C28F MN101C28L MN101CP28D MN101CP28L
Internal ROM type
Mask ROM
EPROM
ROM (byte)
32K
48K
64K
96K
64K
96K
RAM (byte)
1.5K
2K
4K
10K
2K
10K
Package (Lead-free)
LQFP080-P-1414A,
QFP084-P-1818E,
TQFP080-P-1212D
LQFP080-P-1414A
LQFP080-P-1414A,
QFP084-P-1818E,
TQFP080-P-1212D
LQFP080-P-1414A
Minimum Instruction
Execution Time
0.10 s (at 4.5 V to 5.5 V, 20 MHz)
0.238 s (at 2.6 V to 5.5 V, 8.39 MHz)
0.333 s (at 2.3 V to 5.5 V, 6 MHz)
1.00 s (at 2.0 V to 5.5 V, 2 MHz)*
125 s (at 2.0 V to 5.5 V, 32.768 kHz)*
*: The lower limit for operation guarantee for EPROM built-in type is 2.3 V.
Interrupts
RESET. Watchdog. External 0 to 4. Timer 0 to 5. Time base. Serial 0 to 2. Automatic transfer nish. A/D conversion nish
Timer Counter
8-bit timer × 4
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave/8-bit PWM output. Event count. Synchronous output event
Timer 3 ..................Square-wave output. Event count. Remote control carrier output. Serial 0 baud rate timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 4 ..................Square-wave/16-bit PWM output. Event count. Synchronous output event. Input capture
Time base timer: One-minute count setting. Independently operable 8-bit timer 5
Watchdog timer × 1
Serial interface
Synchronous type/Simple UART (half-duplex) × 1: Serial 0
Synchronous type × 1: Serial 1
Synchronous type/Single-master I2C × 1: Serial 2
I/O Pins
I/O
57 : Common use. Specied pull-up resistor available. Input/output selectable (bit unit)
Input
13 : Common use. Specied pull-up resistor available
A/D converter
10-bit × 8 channels (with S/H)
Special Ports
Buzzer output. Remote control carrier output. High-current drive port
Electrical Charactreistics (Supply current)
Parameter
Symbol
Condition
Limit
Unit
min
typ
max
Operating supply current
IDD1
fosc = 20 MHz. VDD = 5 V
25
50
mA
IDD2
fx = 32.768 kHz. VDD = 3 V
40
120
A
Supply current at HALT
IDD3
fx = 32.768 kHz. VDD = 3 V. Ta = 25 °C
4
8
A
fx = 32.768 kHz. VDD = 3 V. Ta = 85 °C
20
A
Supply current at STOP
IDD4
VDD = 5 V. Ta = 25 °C
1
A
VDD = 5 V. Ta = -40 °C to +85 °C
30
A
Development tools
In-circuit Emulator
PX-ICE101C/D + PX-PRB101C28-TQFP080-P-1212
PX-ICE101C/D + PX-PRB101C28-QFP084-P-1818E
PX-ICE101C/D + PX-PRB101C28-LQFP080-P-1414A