- 您现在的位置：买卖IC网 > PDF目录32399 > MP02G260-10 (DYNEX SEMICONDUCTOR LTD) 267 A, 1000 V, SILICON, RECTIFIER DIODE PDF资料下载
参数资料
| 型号： | MP02G260-10 |
| 厂商： | DYNEX SEMICONDUCTOR LTD |
| 元件分类： | 整流器 |
| 英文描述： | 267 A, 1000 V, SILICON, RECTIFIER DIODE |
| 封装： | MP02, 3 PIN |
| 文件页数： | 6/7页 |
| 文件大小： | 102K |
| 代理商： | MP02G260-10 |
6/7
www.dynexsemi.com
MP02XX260 Series
PACKAGE DETAILS
For further package information, please visit our website or contact your nearest Customer Service Centre. All dimensions in mm, unless
stated otherwise. DO NOT SCALE.
MOUNTING RECOMMENDATIONS
Adequate heatsinking is required to maintain the base
temperature at 75C if full rated current is to be achieved. Power
dissipation may be calculated by use of V
T(TO) and rT information
in accordance with standard formulae. We can provide
assistance with calculations or choice of heatsink if required.
The heatsink surface must be smooth and flat; a surface finish
of N6 (32
in) and a flatness within 0.05mm (0.002") are
recommended.
Immediately prior to mounting, the heatsink surface should be
lightly scrubbed with fine emery, Scotch Brite or a mild chemical
etchant and then cleaned with a solvent to remove oxide build
up and foreign material. Care should be taken to ensure no
foreign particles remain.
An even coating of thermal compound (eg. Unial) should be
applied to both the heatsink and module mounting surfaces.
This should ideally be 0.05mm (0.002") per surface to ensure
optimum thermal performance.
After application of thermal compound, place the module
squarely over the mounting holes, (or ‘T’ slots) in the heatsink.
Fit and finger tighten the recommended fixing bolts at each end.
Using a torque wrench, continue to tighten the fixing bolts by
rotating each bolt in turn no more than 1/4 of a revolution at a
time, until the required torque of 6Nm (55lbs.ins) is reached on
all bolts at both ends.
It is not acceptable to fully tighten one fixing bolt before starting
to tighten the others. Such action may DAMAGE the module.
23
24
13
80
34
30
94
3x M6
12.8
2 holes 6.5
12
3
Nominal weight: 350g
Recommended fixings for mounting: M6 socket head cap screws
Recommended mounting torque: 6Nm (55lb.ins)
Recommended torque for electrical connections: 5Nm (44lb.ins)
Maximum torque for electrical connections: 8Nm (70lb.ins)
Module outline type code: MP02
12
3
12
3
12
3
Circuit type: HB
Circuit type: GN
Circuit type: G
相关PDF资料 |
PDF描述 |
|---|---|
| MP251WGP | 25 A, 100 V, SILICON, BRIDGE RECTIFIER DIODE |
| MP254WGPP | 25 A, 400 V, SILICON, BRIDGE RECTIFIER DIODE |
| MP2510WGPP | 25 A, 1000 V, SILICON, BRIDGE RECTIFIER DIODE |
| MP2505WGPP | 25 A, 50 V, SILICON, BRIDGE RECTIFIER DIODE |
| MP2505WGP | 25 A, 50 V, SILICON, BRIDGE RECTIFIER DIODE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MP02S | 制造商:CHENG-YI 制造商全称:CHENG-YI ELECTRONIC CO., LTD. 功能描述:15/25/35 AMPS. SILICON BRIDGE RECTIFIERS |
| MP02TT200 | 制造商:DYNEX 制造商全称:Dynex Semiconductor 功能描述:Dual Thyristor Water Cooled Module Preliminary Information |
| MP02TT200-12 | 制造商:DYNEX 制造商全称:Dynex Semiconductor 功能描述:Dual Thyristor Water Cooled Module Preliminary Information |
| MP02TT200-13 | 制造商:DYNEX 制造商全称:Dynex Semiconductor 功能描述:Dual Thyristor Water Cooled Module Preliminary Information |
| MP02TT200-14 | 制造商:DYNEX 制造商全称:Dynex Semiconductor 功能描述:Dual Thyristor Water Cooled Module Preliminary Information |
发布紧急采购，3分钟左右您将得到回复。