- 您现在的位置：买卖IC网 > PDF目录385630 > MP108 (APEX MICROTECHNOLOGY CORP) POWER OPERATIONAL AMPLIFIER PDF资料下载
参数资料
| 型号： | MP108 |
| 厂商： | APEX MICROTECHNOLOGY CORP |
| 元件分类： | 运动控制电子 |
| 英文描述： | POWER OPERATIONAL AMPLIFIER |
| 中文描述： | OP-AMP, 5000 uV OFFSET-MAX, 10 MHz BAND WIDTH, DMA34 |
| 封装： | DIP-34 |
| 文件页数： | 4/4页 |
| 文件大小： | 298K |
| 代理商： | MP108 |
APEX MICROTECHNOLOGY CORPORATION 5980 NORTH SHANNON ROAD TUCSON, ARIZONA 85741 USA APPLICATIONS HOTLINE: 1 (800) 546-2739
4
OPERATING
CONSIDERATIONS
MP108 MP108A
MP108 REV C JANUARY 2005 2005 Apex Microtechnology Corp.
GENERAL
Please read Application Note 1 "General Operating Consid-
erations" which covers stability, power supplies, heat sinking,
mounting, current limit, SOA interpretation, and specification
interpretation. Visit www.apexmicrotech.com for design tools
that help automate tasks such as calculations for stability,
internal power dissipation, current limit, heat sink selection,
Apex's complete Application Notes library, Technical Seminar
Workbook and Evaluation Kits.
GROUND PINS
The MP108 has two ground pins (pins 3, 32). These pins
provide a return for the internal capacitive bypassing of the
small signal portions of the MP108. The two ground pins are
not
connected together on the substrate. Both of these pins
are required to be connected to the system signal ground.
SAFE OPERATING AREA
The MOSFET output stage of the MP108 is not limited by
second breakdown considerations as in bipolar output stages.
Only thermal considerations and current handling capabilities
limit the SOA (see Safe Operating Area graph on previous page).
The output stage is protected against transient flyback by the
parasitic body diodes of the output stage MOSFET structure.
However, for protection against sustained high energy flyback
external fast-recovery diodes must be used.
COMPENSATION
The external compensation capacitor C
C
is connected
between pins 5 and 6. Unity gain stability can be achieved with
any capacitor value larger than 100pF for a minimum phase
margin of 45 degrees. At higher gains more phase shift can
usually be tolerated in most designs and the compensation
capacitor value can be reduced resulting in higher bandwidth
and slew rate. Use the typical operating curves as a guide to
select C
C
for the application. An NPO (COG) type capacitor
is required rated for the full supply voltage (200V).
OVERVOLTAGE PROTECTION
Although the MP108 can withstand differential input voltages
up to ±25V, additional external protection is recommended. In
most applications 1N4148 signal diodes connected anti-parallel
across the input pins is sufficient. In more demanding applica-
tions where bias current is important diode connected JFETs
such as 2N4416 will be required. See Q1 and Q2 in Figure
1. In either case the differential input voltage will be clamped
to ±0.7V. This is usually sufficient overdrive to produce the
maximum power bandwidth. Some applications will also need
over voltage protection devices connected to the power supply
rails. Unidirectional zener diode transient suppressors are rec-
ommended. The zeners clamp transients to voltages within the
power supply rating and also clamp power supply reversals to
ground. Whether the zeners are used or not the system power
supply should be evaluated for transient performance including
power-on overshoot and power-off polarity reversals as well
as line regulation. See Z1 and Z2 in Figure 1.
POWER SUPPLY BYPASSING
Bypass capacitors to power supply terminals +V
S
and -V
S
must be connected physically close to the pins to prevent local
parasitic oscillation in the output stage of the MP108. Use
electrolytic capacitors at least 10μF per output amp required.
Bypass the electrolytic capacitors with high quality ceramic
capacitors (X7R) 0.1μF or greater. In most applications power
supply terminals +V
B
and -V
B
will be connected to +V
S
and
-V
S
respectively. Supply voltages +V
B
and -V
B
are bypassed
internally but both ground pins 3 and 32 must be connected to
the system signal ground to be effective. In all cases power to
the buffer amplifier stage of the MP108 at pins 8 and 25 must
be connected to +V
B
and -V
B
at pins 4 and 30 respectively.
Provide local bypass capacitors at pins 8 and 25. See the
external connections diagram on page 1.
FIGURE 1
OVERVOLTAGE PROTECTION
CURRENT LIMIT
The two current limit sense lines are to be connected directly
across the current limit sense resistor. For the current limit to
work correctly pin 28 must be connected to the amplifier output
side and pin 27 connected to the load side of the current limit
resistor R
LIM
as shown in Figure 2. This connection will bypass
any parasitic resistances RP, formed by socket and solder joints
as well as internal amplifier losses. The current limiting resistor
may not be placed anywhere in the output circuit except where
shown in Figure 2. The value of the current limit resistor can
be calculated as follows: R
LIM
= .65/I
LIMIT
BOOST OPERATION
With the boost feature the small signal stages of the amplifier
are operated at a higher supply voltages than the amplifierís
high current output stage. +V
B
(pins 4,8) and -V
B
(pins 25,30)
are connected to the small signal stages and +V
S
(pins 14-16)
and -V
S
(pins 17-19) are connected to the high current output
stage. An additional 10V on the +V
B
and -V
B
pins is sufficient
to allow the small signal stages to drive the output stage into
the triode region and improve the output voltage swing for extra
efficient operation when required. When the boost feature is
not needed +V
S
and -V
S
are connected to the +V
B
and -V
B
pins
respectively. The +V
B
and -V
B
pins must not be operated at
supply voltages less than +V
S
and -V
S
respectively.
BACKPLATE GROUNDING
The substrate of the MP108 is an insulated metal substrate.
It is required that it be connected to signal ground. Connect pin
2 (back plate) to signal ground. The back plate will then be AC
grounded to signal ground through a 1μF capacitor.
FIGURE 2
4 WIRE CURRENT LIMIT
相关PDF资料 |
PDF描述 |
|---|---|
| MP108A | POWER OPERATIONAL AMPLIFIER |
| MP10 | Power Rheostats |
| MP10A1500 | Power Rheostats |
| MP2.5CRP | RFCO-AXIAL CONNECTORS |
| MP2.5CPA-JJ | RFCO-AXIAL CONNECTORS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MP-108300 | 功能描述:标准环形接头 Crimp Pin contacts 13-85-SZ 18 RoHS:否 制造商:TE Connectivity / AMP 系列:Multimate III+ 触点尺寸: 触点类型:Pin (Male) 触点材料: 触点电镀:Tin over Nickel 触点类型2: 电流额定值:13 A 电压额定值: |
| MP-108400 | 功能描述:标准环形接头 COMBO PIN CONTACTS 13-85-SZ 16 RoHS:否 制造商:TE Connectivity / AMP 系列:Multimate III+ 触点尺寸: 触点类型:Pin (Male) 触点材料: 触点电镀:Tin over Nickel 触点类型2: 电流额定值:13 A 电压额定值: |
| MP-108500 | 功能描述:标准环形接头 CRIMP SOCKET CONTACT 150-SZ 18 RoHS:否 制造商:TE Connectivity / AMP 系列:Multimate III+ 触点尺寸: 触点类型:Pin (Male) 触点材料: 触点电镀:Tin over Nickel 触点类型2: 电流额定值:13 A 电压额定值: |
| MP-108600 | 功能描述:标准环形接头 COMBO SOCKET CONT 13-85-SZ 16 RoHS:否 制造商:TE Connectivity / AMP 系列:Multimate III+ 触点尺寸: 触点类型:Pin (Male) 触点材料: 触点电镀:Tin over Nickel 触点类型2: 电流额定值:13 A 电压额定值: |
| MP108A | 制造商:APEX 制造商全称:APEX 功能描述:POWER OPERATIONAL AMPLIFIER |
发布紧急采购，3分钟左右您将得到回复。