- 您现在的位置：买卖IC网 > PDF目录296599 > MP28372DS-LF (MONOLITHIC POWER SYSTEMS INC) 3 A DUAL SWITCHING CONTROLLER, 1400 kHz SWITCHING FREQ-MAX, PDSO16 PDF资料下载
参数资料
| 型号： | MP28372DS-LF |
| 厂商： | MONOLITHIC POWER SYSTEMS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 3 A DUAL SWITCHING CONTROLLER, 1400 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | LEAD FREE, SOIC-16 |
| 文件页数： | 10/12页 |
| 文件大小： | 268K |
| 代理商： | MP28372DS-LF |
MP28372 — DUAL 1.5A, 23V, 1.4MHz STEP-DOWN CONVERTER
MP28372 Rev. 1.4
www.MonolithicPower.com
7
12/10/2007
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
2007 MPS. All Rights Reserved.
TM
APPLICATION INFORMATION
COMPONENT SELECTION
The MP28372 has two channels: A and B. The
following formulas are used for component
selection of both channels. Refer to
components with reference “A” for channel A,
and components with reference “B” for channel
B, respectively, as indicated in Figure 3 (i.e. –
R1A for Channel A and R1B for Channel B).
Setting the Output Voltage
The output voltage is set using a resistive
voltage divider from the output voltage to FB pin.
The voltage divider divides the output voltage
down to the feedback voltage by the ratio:
2
R
1
R
2
R
V
OUT
FB
+
=
Thus the output voltage is:
2
R
2
R
1
R
V
92
.
0
VOUT
+
×
=
Where VFB is the feedback voltage and VOUT is
the output voltage
A typical value for R2 can be as high as 100k,
but a typical value is 10k. Using that value, R1
is determined by:
)
1
V
92
.
0
V
(
2
R
1
R
OUT
×
=
For example, for a 3.3V output voltage, R2 is
10k, and R1 is 25.9k.
Inductor
The inductor is required to supply constant
current to the output load while being driven by
the switched input voltage. A larger value
inductor will result in less ripple current that will
result in lower output ripple voltage. However,
the larger value inductor will have a larger
physical size, higher series resistance, and/or
lower saturation current. A good rule for
determining the inductance to use is to allow
the peak-to-peak ripple current in the inductor
to be approximately 30% of the maximum
switch current limit. Also, make sure that the
peak inductor current is below the maximum
switch current limit. The inductance value can
be calculated by:
×
=
IN
OUT
L
S
OUT
V
1
ΔI
f
V
1
L
Where VIN is the input voltage, fS is the
switching frequency, and ΔIL is the peak-to-
peak inductor ripple current.
Choose an inductor that will not saturate under
the maximum inductor peak current.
The peak inductor current can be calculated by:
×
+
=
IN
OUT
S
OUT
LOAD
LP
V
1
L
f
2
V
I
Where ILOAD is the load current.
Output Rectifier Diode
The output rectifier diode supplies the current to
the inductor when the high-side switch is off. To
reduce losses due to the diode forward voltage
and recovery times, use a Schottky diode.
Choose a diode whose maximum reverse
voltage rating is greater than the maximum
input voltage, and whose current rating is
greater than the maximum load current.
Input Capacitor
The input current to the step-down converter is
discontinuous, therefore a capacitor is required
to supply the AC current to the step-down
converter while maintaining the DC input
voltage. Use low ESR capacitors for the best
performance. Ceramic capacitors are preferred,
but tantalum or low-ESR electrolytic capacitors
may also suffice.
Since the input capacitor (C1) absorbs the input
switching current it requires an adequate ripple
current rating. The RMS current in the input
capacitor can be estimated by:
×
×
=
IN
OUT
IN
OUT
LOAD
1
C
V
1
V
I
The worst-case condition occurs at VIN = 2VOUT,
where:
2
I
LOAD
1
C =
相关PDF资料 |
PDF描述 |
|---|---|
| MP62061DH | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| MP62340DS-LF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| MP74-1 | INTERCONNECTION DEVICE |
| MPA52-16MHZ | CRYSTAL OSCILLATOR, CLOCK, 16 MHz, CMOS/TTL OUTPUT |
| MPA54-FREQ | CRYSTAL OSCILLATOR, CLOCK, 16 MHz - 150 MHz, CMOS/TTL OUTPUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MP28490DN-LF | 功能描述:开关变换器、稳压器与控制器 5V, 30V, 420KHz Buck Non-Sync Buck RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MP28490DN-LF-Z | 功能描述:开关变换器、稳压器与控制器 5V, 30V, 420KHz Buck Non-Sync Buck RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MP28493DS-LF | 功能描述:开关变换器、稳压器与控制器 3A 4.5V 30V 420KHz Sync Buck RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MP28493DS-LF-Z | 功能描述:开关变换器、稳压器与控制器 3A 4.5V 30V 420KHz Sync Buck RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MP28W23F | 功能描述:CONTACT PIN CRIMP 28-30AWG GOLD RoHS:是 类别:连接器，互连式 >> 圆形 - 触点 系列:RT360™, RT 产品变化通告:84590 Series Obsolescence 21/Dec/2010 标准包装:10 系列:超坚固圆形 (XRC™) 引脚或插口:引脚 类型:带印记 尺寸:16 线规:14-18 AWG 触点终端:压接 触点表面涂层:镍 触点涂层厚度:80µin（2.03µm） 包装:剪切带 (CT) 产品目录页面:435 (CN2011-ZH PDF) 工具箱:WM8469-ND - KIT CIRCULAR XRC PLUGS & RECPT 配用:WM4675-ND - CONN PLUG 31POS W/PIN SEALEDWM4674-ND - CONN RCPT 31POS W/PIN SEALEDWM1062-ND - CONN PLUG W/PIN SEALED 14POSWM1061-ND - CONN RCPT W/PINS SEALED 14POS 相关产品:0638678200-ND - FINE ADJUST APPLICATOR0638678100-ND - FINE ADJUST APPLICATORWM4790-ND - MOLEX HAND CRIMP TOOL 其它名称:WM1065CT |
发布紧急采购，3分钟左右您将得到回复。