参数资料
型号: MP80C51C-30D
厂商: TEMIC SEMICONDUCTORS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 30 MHz, MICROCONTROLLER, PDIP40
文件页数: 16/170页
文件大小: 4133K
代理商: MP80C51C-30D
112
ATtiny4/5/9/10 [DATASHEET]
8127F–AVR–02/2013
15.4.3.4
Erasing the Configuration Section
The algorithm for erasing the Configuration section is as follows:
1.
Write the SECTION_ERASE command to the NVMCMD register
2.
Start the erase operation by writing a dummy byte to the high byte of any word location inside the configu-
ration section
3.
Wait until the NVMBSY bit has been cleared
15.4.3.5
Writing a Configuration Word
The algorithm for writing a Configuration word is as follows.
1.
Write the WORD_WRITE command to the NVMCMD register
2.
Write the low byte of the data to the low byte of a configuration word location
3.
Write the high byte of the data to the high byte of the same configuration word location. This will start the
Flash write operation.
4.
Wait until the NVMBSY bit has been cleared
15.4.4
Reading NVM Lock Bits
The Non-Volatile Memory Lock Byte can be read from the mapped location in data memory.
15.4.5
Writing NVM Lock Bits
The algorithm for writing the Lock bits is as follows.
1.
Write the WORD_WRITE command to the NVMCMD register.
2.
Write the lock bits value to the Non-Volatile Memory Lock Byte location. This is the low byte of the Non-
Volatile Memory Lock Word.
3.
Start the NVM Lock Bit write operation by writing a dummy byte to the high byte of the NVM Lock Word
location.
4.
Wait until the NVMBSY bit has been cleared.
15.5
Self programming
The ATtiny4/5/9/10 don't support internal programming.
15.6
External Programming
The method for programming the Non-Volatile Memories by means of an external programmer is referred to as
external programming. External programming can be done both in-system or in mass production.
The Non-Volatile Memories can be externally programmed via the Tiny Programming Interface (TPI). For details
on the TPI, see “Programming interface” on page 95. Using the TPI, the external programmer can access the NVM
control and status registers mapped to I/O space and the NVM memory mapped to data memory space.
15.6.1
Entering External Programming Mode
The TPI must be enabled before external programming mode can be entered. The following procedure describes,
how to enter the external programming mode after the TPI has been enabled:
1.
Make a request for enabling NVM programming by sending the NVM memory access key with the SKEY
instruction.
2.
Poll the status of the NVMEN bit in TPISR until it has been set.
相关PDF资料
PDF描述
MF180C31-12R 8-BIT, 12 MHz, MICROCONTROLLER, PQFP44
MS80C51C-20D 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQCC44
MT80C51-36D 8-BIT, MROM, 36 MHz, MICROCONTROLLER, PQFP44
MT80C51C-12D 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP44
MP80C51C-20D 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PDIP40
相关代理商/技术参数
参数描述
MP81 制造商:未知厂家 制造商全称:未知厂家 功能描述:BRIDGE RECTIFIERS
MP810 制造商:GOOD-ARK 制造商全称:GOOD-ARK Electronics 功能描述:SILICON BRIDGE RECTIFIERS
MP-810 制造商:JAMECO BENCHPRO 功能描述:4-Piece Plier/Cutter/Screwdrivers Set
MP8100 制造商:MPS 制造商全称:Monolithic Power Systems 功能描述:Precision High-Side Current-Sense Amplifier
MP8100DS 制造商:MPS 制造商全称:Monolithic Power Systems 功能描述:Precision High-Side Current-Sense Amplifier