参数资料
型号: MPC17529EV
厂商: Freescale Semiconductor
文件页数: 8/15页
文件大小: 0K
描述: IC MOTOR DRVR H-BRDG DUAL 20-MFP
标准包装: 70
应用: DC 电机驱动器,步进电机驱动器,H 桥式
输出数: 1
电流 - 输出: 700mA
电压 - 负载: 2 V ~ 6.8 V
电源电压: 2.7 V ~ 5.6 V
工作温度: -20°C ~ 65°C
安装类型: 表面贴装
封装/外壳: 20-SSOP(0.209",5.30mm 宽)
供应商设备封装: 20-VMFP
包装: 管件
SYSTEM / APPLICATION INFORMATION
INTRODUCTION
SYSTEM / APPLICATION INFORMATION
INTRODUCTION
The 17529 is a monolithic dual H-Bridge ideal for portable
electronic applications to control bipolar step motors and
brush DC motors, such as those found in camera lens
assemblies, camera shutters, optical disk drives, etc. The
17529 operates from 2.0 V to 6.8 V, providing dual H-bridge
motor drivers with parallel 3.0 V or 5.0 V compatible I/O. The
device features an on-board charge pump, as well as built-in
shoot-through current protection and undervoltage
The 17529 has four operating modes: forward, reverse,
brake, and tri-stated (high-impedance). The MOSFETs
comprising the output bridge have a total source + sink
R DS(ON) ≤ 1.2 Ω .
The 17529 can simultaneously drive two brush DC motors
Diagram on page 1, one bipolar step motor. The drivers are
designed to be PWM’ed at frequencies up to 200 kHz.
shutdown.
FUNCTIONAL PIN DESCRIPTION
CONTROL CIRCUIT POWER SUPPLY (VDD)
The VDD pin carries the logic supply voltage and current
into the logic sections of the IC. VDD has an undervoltage
threshold. If the supply voltage drops below the undervoltage
threshold, the output power stage switches to a tri-state
condition. When the supply voltage returns to a level that is
above the threshold, the power stage automatically resumes
normal operation according to the established condition of
the input pins.
LOGIC INPUT CONTROL (IN1A, IN1B, IN2A, AND
IN2B)
These logic input pins control each H-Bridge output. IN1A
logic HIGH = OUT1A HIGH. However, if all inputs are taken
HIGH, the outputs bridges are both tri-stated (refer to Table
5, Truth Table , page 7 ).
OUTPUT ENABLE (OE)
The OE pin is a LOW = TRUE enable input. When
OE = HIGH, all H-Bridge outputs (OUT1A, OUT1B, OUT2A,
and OUT2B) are tri-stated (high-impedance), regardless of
logic input (IN1A, IN1B, IN2A, and IN2B) states.
H-BRIDGE OUTPUT (OUT1A, OUT1B, OUT2A, AND
OUT2B)
MOTOR DRIVE POWER SUPPLY (VM1 AND VM2)
The VM pins carry the main supply voltage and current into
the power sections of the IC. This supply then becomes
controlled and/or modulated by the IC as it delivers the power
to the loads attached between the output pins. All VM pins
must be connected together on the printed circuit board.
CHARGE PUMP (C1L AND C1H, C2L AND C2H)
These two pairs of pins, the C1L and C1H and the C2L and
C2H, connect to the external bucket capacitors required by
the internal charge pump. The typical value for the bucket
capacitors is 0.1 μ F.
PRE-DRIVER POWER SUPPLY (CRES)
The CRES pin is the output of the internal charge pump.
Its output voltage is approximately three times the V DD
voltage. The V CRES voltage is power supply for internal pre-
driver circuit of H-Bridges.
POWER GROUND (PGND)
Power ground pins. They must be tied together on the
PCB.
LOGIC GROUND (LGND)
Logic ground pin.
These pins provide connection to the outputs of each of
the internal H-Bridges (see Figure 2, 17529 Simplified
17529
Analog Integrated Circuit Device Data
8
Freescale Semiconductor
相关PDF资料
PDF描述
VE-2TW-EX CONVERTER MOD DC/DC 5.5V 75W
RCM15DTBI CONN EDGECARD 30POS R/A .156 SLD
6278199-2 C/A, ST TO MT-RJ 2M1
SP809NEK-L-2-3/TR IC MPU RESET CIRC 2.3V SOT23-3
VE-20W-EX CONVERTER MOD DC/DC 5.5V 75W
相关代理商/技术参数
参数描述
MPC17529EV 制造商:Freescale Semiconductor 功能描述:Load Switch IC
MPC17529EV/EL 制造商:Freescale Semiconductor 功能描述:
MPC17529EVEL 功能描述:电源管理IC开发工具 Motor Driver RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
MPC17531A 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:700 mA Dual H-Bridge Motor Driver with 3.0 V Compatible Logic I/O
MPC17531A_08 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:700 mA Dual H-Bridge Motor Driver with 3.0 V Compatible Logic I/O