参数资料
型号: MPC8379ECVRANG
厂商: Freescale Semiconductor
文件页数: 15/117页
文件大小: 0K
描述: MPU POWERQUICC II PRO 689-PBGA
标准包装: 27
系列: MPC83xx
处理器类型: 32-位 MPC83xx PowerQUICC II Pro
速度: 800MHz
电压: 1.05V
安装类型: 表面贴装
封装/外壳: 689-BBGA 裸露焊盘
供应商设备封装: 689-TEPBGA II(31x31)
包装: 托盘
MPC8379E PowerQUICC II Pro Processor Hardware Specifications, Rev. 8
Freescale Semiconductor
111
These capacitors should have a value of 0.01 or 0.1 F. Only ceramic SMT (surface mount technology)
capacitors should be used to minimize lead inductance, preferably 0402 or 0603 sizes.
In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB,
feeding the VDD, OVDD, GVDD, and LVDD planes, to enable quick recharging of the smaller chip
capacitors. These bulk capacitors should have a low ESR (equivalent series resistance) rating to ensure the
quick response time necessary. They should also be connected to the power and ground planes through two
vias to minimize inductance. Suggested bulk capacitors—100–330 F (AVX TPS tantalum or Sanyo
OSCON).
24.3
Connection Recommendations
To ensure reliable operation, it is highly recommended that unused inputs be connected to an appropriate
signal level. Unused active low inputs should be tied to OVDD, GVDD, or LVDD as required. Unused
active high inputs should be connected to GND. All NC (no-connect) signals must remain unconnected.
Power and ground connections must be made to all external VDD, GVDD, LVDD, OVDD, and GND pins
of the device.
24.4
Output Buffer DC Impedance
The device drivers are characterized over process, voltage, and temperature. For all buses, the driver is a
push-pull single-ended driver type (open drain for I2C).
To measure Z0 for the single-ended drivers, an external resistor is connected from the chip pad to OVDD
or GND. Then, the value of each resistor is varied until the pad voltage is OVDD/2 (see Figure 63). The
output impedance is the average of two components, the resistances of the pull-up and pull-down devices.
When data is held high, SW1 is closed (SW2 is open) and RP is trimmed until the voltage at the pad equals
OVDD/2. RP then becomes the resistance of the pull-up devices. RP and RN are designed to be close to each
other in value. Then, Z0 = (RP + RN)/2.
Figure 63. Driver Impedance Measurement
OVDD
OGND
RP
RN
Pad
Data
SW1
SW2
相关PDF资料
PDF描述
395-012-521-204 CARD EDGE 12POS DL .100X.200 BLK
MPC8379ECVRALG MPU POWERQUICC II PRO 689-PBGA
MPC8379ECVRAJF MPU POWERQUICC II PRO 689-PBGA
395-012-521-202 CARD EDGE 12POS DL .100X.200 BLK
CAT24C32YI-G IC EEPROM SERIAL 32KB I2C 8TSSOP
相关代理商/技术参数
参数描述
MPC8379ECVRANGA 功能描述:微处理器 - MPU 8379 PBGA XT PbFr W/ENC RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
MPC8379ECZQAFDA 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:PowerQUICC? II Pro Processor Hardware Specifications
MPC8379ECZQAFFA 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:PowerQUICC? II Pro Processor Hardware Specifications
MPC8379ECZQAFGA 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:PowerQUICC? II Pro Processor Hardware Specifications
MPC8379ECZQAGDA 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:PowerQUICC? II Pro Processor Hardware Specifications