- 您现在的位置：买卖IC网 > PDF目录80459 > MPC8545EPXAQG (FREESCALE SEMICONDUCTOR INC) 32-BIT, 1000 MHz, MICROPROCESSOR, PBGA783 PDF资料下载
参数资料
| 型号： | MPC8545EPXAQG |
| 厂商： | FREESCALE SEMICONDUCTOR INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 32-BIT, 1000 MHz, MICROPROCESSOR, PBGA783 |
| 封装： | 29 X 29 MM, 1 MM PITCH, FLIP CHIP, PLASTIC, BGA-783 |
| 文件页数： | 36/142页 |
| 文件大小： | 1504K |
| 代理商： | MPC8545EPXAQG |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页当前第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页
MPC8548E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 5
130
Freescale Semiconductor
System Design Information
21.4
SerDes Block Power Supply Decoupling Recommendations
The SerDes block requires a clean, tightly regulated source of power (SVDD and XVDD) to ensure low
jitter on transmit and reliable recovery of data in the receiver. An appropriate decoupling scheme is
outlined below.
Only surface mount technology (SMT) capacitors should be used to minimize inductance. Connections
from all capacitors to power and ground should be done with multiple vias to further reduce inductance.
First, the board should have at least 10
× 10-nF SMT ceramic chip capacitors as close as possible
to the supply balls of the device. Where the board has blind vias, these capacitors should be placed
directly below the chip supply and ground connections. Where the board does not have blind vias,
these capacitors should be placed in a ring around the device as close to the supply and ground
connections as possible.
Second, there should be a 1-F ceramic chip capacitor from each SerDes supply (SVDD and
XVDD) to the board ground plane on each side of the device. This should be done for all SerDes
supplies.
Third, between the device and any SerDes voltage regulator there should be a 10-F, low
equivalent series resistance (ESR) SMT tantalum chip capacitor and a 100-F, low ESR SMT
tantalum chip capacitor. This should be done for all SerDes supplies.
21.5
Connection Recommendations
To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal
level. All unused active low inputs should be tied to VDD, TVDD, BVDD, OVDD, GVDD, and LVDD, as
required. All unused active high inputs should be connected to GND. All NC (no-connect) signals must
remain unconnected. Power and ground connections must be made to all external VDD, TVDD, BVDD,
OVDD, GVDD, LVDD, and GND pins of the device.
21.6
Pull-Up and Pull-Down Resistor Requirements
The MPC8548E requires weak pull-up resistors (2–10 k
Ω is recommended) on open drain type pins
including I2C pins and PIC (interrupt) pins.
Correct operation of the JTAG interface requires configuration of a group of system control pins as
demonstrated in Figure 62. Care must be taken to ensure that these pins are maintained at a valid deasserted
state under normal operating conditions as most have asynchronous behavior and spurious assertion will
give unpredictable results.
The following pins must not be pulled down during power-on reset: TSEC3_TXD[3], HRESET_REQ,
TRIG_OUT/READY/QUIESCE, MSRCID[2:4], ASLEEP. The DMA_DACK[0:1], and TEST_SEL/
TEST_SEL pins must be set to a proper state during POR configuration. Refer to the pinlist table of the
individual device for more details
Refer to the PCI 2.2 specification for all pull ups required for PCI.
相关PDF资料 |
PDF描述 |
|---|---|
| MPC8547EVUAQGB | 32-BIT, 1000 MHz, MICROPROCESSOR, CBGA783 |
| MPC8548CPXAQHA | 32-BIT, 1000 MHz, MICROPROCESSOR, PBGA783 |
| MPC8548CPXAVH | 32-BIT, 1500 MHz, MICROPROCESSOR, PBGA783 |
| MPC8548CVTAQG | 32-BIT, 1000 MHz, MICROPROCESSOR, PBGA783 |
| MPC8548CVUAQJB | 32-BIT, 1000 MHz, MICROPROCESSOR, CBGA783 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MPC8545EPXAQGA | 功能描述:微处理器 - MPU PQ3 8545E Imaging Processor RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| MPC8545EPXAQGB | 功能描述:微处理器 - MPU FG PQ38 8548 RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| MPC8545EPXATGA | 功能描述:微处理器 - MPU PQ3 8545E Imaging Processor RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| MPC8545EPXATGB | 功能描述:微处理器 - MPU FG PQ38 8548 RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| MPC8545EVTANGA | 功能描述:微处理器 - MPU PQ3 8545E Imaging Processor RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
发布紧急采购，3分钟左右您将得到回复。