- 您现在的位置：买卖IC网 > PDF目录69037 > MPC92430FA (INTEGRATED DEVICE TECHNOLOGY INC) 800 MHz, OTHER CLOCK GENERATOR, PQFP32 PDF资料下载
参数资料
| 型号： | MPC92430FA |
| 厂商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分类： | 时钟产生/分配 |
| 英文描述： | 800 MHz, OTHER CLOCK GENERATOR, PQFP32 |
| 封装： | LQFP-32 |
| 文件页数： | 1/12页 |
| 文件大小： | 564K |
| 代理商： | MPC92430FA |
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Order Number: MPC92430/D
Rev 0, 09/2003
1
Motorola, Inc. 2003
800 MHz Low Voltage PECL
Clock Synthesizer
The MPC92430 is a 3.3V compatible, PLL based clock synthesizer
targeted for high performance clock generation in mid-range to
high-performance telecom, networking and computing applications. With
output frequencies from 50 MHz to 800 MHz and the support of differential
PECL output signals the device meets the needs of the most demanding
clock applications.
Features
50 MHz to 800 MHz synthesized clock output signal
Differential PECL output
LVCMOS compatible control inputs
On-chip crystal oscillator for reference frequency generation
Alternative LVCMOS compatible reference clock input
3.3V power supply
Fully integrated PLL
Minimal frequency overshoot
Serial 3-wire programming interface
Parallel programming interface for power-up
32 lead LQFP and 28 PLCC packaging
SiGe Technology
Ambient temperature range 0°Cto+70°C
Pin and function compatible to the MC12430 and MPC9230
Functional Description
The internal crystal oscillator uses the external quartz crystal as the basis of its frequency reference. The frequency of the
internal crystal oscillator is divided by 16 and then multiplied by the PLL. The VCO within the PLL operates over a range of 400 to
800 MHz. Its output is scaled by a divider that is configured by either the serial or parallel interfaces. The crystal oscillator
frequency fXTAL, the PLL feedback-divider M and the PLL post-divider N determine the output frequency.
The feedback path of the PLL is internal. The PLL adjusts the VCO output frequency to be 2M times the reference frequency
by adjusting the VCO control voltage. Note that for some values of M (either too high or too low) the PLL will not achieve phase
lock. The PLL will be stable if the VCO frequency is within the specified VCO frequency range (400 to 800 MHz). The M-value
must be programmed by the serial or parallel interface.
The PLL post-divider N is configured through either the serial or the parallel interfaces, and can provide one of four division
ratios (1, 2, 4, or 8). This divider extends performance of the part while providing a 50% duty cycle. The output driver is driven
differentially from the output divider, and is capable of driving a pair of transmission lines terminated 50 to VCC –2.0V. The
positive supply voltage for the internal PLL is separated from the power supply for the core logic and output drivers to minimize
noise induced jitter.
The configuration logic has two sections: serial and parallel. The parallel interface uses the values at the M[8:0] and N[1:0]
inputs to configure the internal counters. It is recommended on system reset to hold the P_LOAD input LOW until power becomes
valid. On the LOW–to–HIGH transition of P_LOAD, the parallel inputs are captured. The parallel interface has priority over the
serial interface. Internal pullup resistors are provided on the M[8:0] and N[1:0] inputs prevent the LVCMOS compatible control
inputs from floating.
The serial interface centers on a fourteen bit shift register. The shift register shifts once per rising edge of the S_CLOCK input.
The serial input S_DATA must meet setup and hold timing as specified in the AC Characteristics section of this document. The
configuration latches will capture the value of the shift register on the HIGH–to–LOW edge of the S_LOAD input. See the
programming section for more information. The TEST output reflects various internal node values, and is controlled by the T[2:0]
bits in the serial data stream. In order to minimize the PLL jitter, it is recommended to avoid active signal on the TEST output.
FA SUFFIX
32 LEAD LQFP PACKAGE
CASE 873A
800 MHZ LOW VOLTAGE
CLOCK SYNTHESIZER
FN SUFFIX
28 LEAD PLCC PACKAGE
CASE 776
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
DATA SHEET
MPC92430
IDT 800 MHz Low Voltage PECL Clock Synthesizer
Freescale Timing Solutions Organization has been acquired by Integrated Device Technology, Inc
MPC92430
1
800 MHz Low Voltage PECL Clock
Synthesizer
相关PDF资料 |
PDF描述 |
|---|---|
| MPC92430FN | 800 MHz, OTHER CLOCK GENERATOR, PQCC28 |
| MPC92432AE | 1360 MHz, OTHER CLOCK GENERATOR, PQFP48 |
| MPC9299FA | 400 MHz, OTHER CLOCK GENERATOR, PQFP32 |
| MPC930FA | 140 MHz, PROC SPECIFIC CLOCK GENERATOR, PQFP32 |
| MPC930FA | 140 MHz, PROC SPECIFIC CLOCK GENERATOR, PQFP32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MPC92432 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:1360 MHz Dual Output LVPECL Clock Synthesizer |
| MPC92432AE | 功能描述:时钟合成器/抖动清除器 FSL 1360MHz Dual Out put LVPECL Clock Syn RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| MPC92432AER2 | 功能描述:时钟合成器/抖动清除器 FSL 1360MHz Dual Out put LVPECL Clock Syn RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| MPC92432FA | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:1360 MHz Dual Output LVPECL Clock Synthesizer |
| MPC92433 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:1428 MHz Dual Output LVPECL Clock Synthesizer |
发布紧急采购，3分钟左右您将得到回复。