- 您现在的位置：买卖IC网 > PDF目录8741 > MPC9448AC (IDT, Integrated Device Technology Inc)IC CLOCK BUFFER MUX 1:12 32-LQFP PDF资料下载
参数资料
| 型号： | MPC9448AC |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 11/13页 |
| 文件大小： | 0K |
| 描述： | IC CLOCK BUFFER MUX 1:12 32-LQFP |
| 标准包装： | 250 |
| 类型： | 扇出缓冲器（分配），多路复用器 |
| 电路数： | 1 |
| 比率 - 输入:输出： | 1:12 |
| 差分 - 输入:输出： | 是/无 |
| 输入： | LVCMOS，LVPECL |
| 输出： | LVCMOS |
| 频率 - 最大： | 350MHz |
| 电源电压： | 2.375 V ~ 3.465 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-LQFP |
| 供应商设备封装： | 32-TQFP（7x7） |
| 包装： | 托盘 |
| 其它名称： | 800-2011 MPC9448ACIDT-ND |
MPC9448 REVISION 7 DECEMBER 21, 2012
7
2012 Integrated Device Technology, Inc.
MPC9448 Data Sheet
3.3V/2.5V LVCMOS 1:12 CLOCK FANOUT BUFFER
Since this step is well above the threshold region, it will not
cause any false clock triggering; however, designers may be
uncomfortable with unwanted reflections on the line. To better
match the impedances when driving multiple lines, the
situation in Figure 6 should be used. In this case, the series
terminating resistors are reduced such that when the parallel
combination is added to the output buffer impedance, the line
impedance is perfectly matched.
Figure 6. Optimized Dual Line Termination
Power Consumption of the MPC9448 and
Thermal Management
The MPC9448 AC specification is guaranteed for the
entire operating frequency range up to 350 MHz. The
MPC9448 power consumption, and the associated long-term
reliability, may decrease the maximum frequency limit,
depending on operating conditions such as clock frequency,
supply voltage, output loading, ambient temperature, vertical
convection and thermal conductivity of package and board.
This section describes the impact of these parameters on the
junction temperature and gives a guideline to estimate the
MPC9448 die junction temperature and the associated
device reliability. For a complete analysis of power
consumption as a function of operating conditions and
associated long term device reliability, please refer to the
Freescale application note AN1545. According the AN1545,
the long-term device reliability is a function of the die junction
temperature:
Increased power consumption will increase the die
junction temperature and impact the device reliability
(MTBF). According to the system-defined tolerable MTBF,
the die junction temperature of the MPC9448 needs to be
controlled, and the thermal impedance of the board/package
should be optimized. The power dissipated in the MPC9448
is represented in equation 1.
Where ICCQ is the static current consumption of the
MPC9448, CPD is the power dissipation capacitance per
output.
CL represents the external capacitive output
load, and N is the number of active outputs (N is always 12 in
case of the MPC9448). The MPC9448 supports driving
transmission lines to maintain high signal integrity and tight
timing parameters. Any transmission line will hide the lumped
capacitive load at the end of the board trace, therefore,
CL
is zero for controlled transmission line systems and can be
eliminated from equation 1. Using parallel termination output,
termination results in equation 2 for power dissipation.
In equation 2, P stands for the number of outputs with a
parallel or thevenin termination. VOL, IOL, VOH and IOH are a
function of the output termination technique, and DCQ is the
clock signal duty cycle. If transmission lines are used,
CL is
zero in equation 2 and can be eliminated. In general, the use
of controlled transmission line techniques eliminates the
impact of the lumped capacitive loads at the end lines and
greatly reduces the power dissipation of the device.
Equation 3 describes the die junction temperature TJ as a
function of the power consumption.
Where Rthja is the thermal impedance of the package
(junction to ambient), and TA is the ambient temperature.
According to Figure 9, the junction temperature can be used
to estimate the long-term device reliability. Further, combining
equation 1 and equation 2 results in a maximum operating
frequency for the MPC9448 in a series terminated
transmission line system, equation 4.
17
MPC9448
Output
Buffer
RS = 16
ZO = 50
RS = 16
ZO = 50
17
+ 16 || 16 = 50 || 50
25
= 25
Table 9. Die Junction Temperature and MTFB
Junction Temperature (
C)
MTBF (Years)
100
20.4
110
9.1
120
4.2
130
2.0
PTOT = [ ICCQ + VCC fCLOCK ( N CPD + CL ) ] VCC
M
PTOT = VCC [ ICCQ + VCC fCLOCK ( N CPD + CL ) ] + [ DCQ IOH (VCC – VOH) + (1 – DCQ) IOL VOL ]
M
P
TJ = TA + PTOT Rthja
Equation 1
Equation 2
Equation 3
Equation 4
fCLOCK,MAX =
CPD N V2CC
1
[
– (ICCQ VCC)
]
Rthja
Tj,MAX – TA
相关PDF资料 |
PDF描述 |
|---|---|
| VI-21Y-MU-F2 | CONVERTER MOD DC/DC 3.3V 132W |
| ICS83058AGILF | IC CLOCK MUX 8:1 250MHZ 16-TSSOP |
| VI-27T-MW-F3 | CONVERTER MOD DC/DC 6.5V 100W |
| ICS853S011BMILF | IC CLOCK BUFFER 1:2 2.5GHZ 8SOIC |
| SY89311UMG TR | IC CLOCK BUFFER 1:2 3GHZ 8-MLF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MPC9448ACR2 | 功能描述:时钟缓冲器 FSL 1-12 LVCMOS Fanout Buffer RoHS:否 制造商:Texas Instruments 输出端数量:5 最大输入频率:40 MHz 传播延迟（最大值）: 电源电压-最大:3.45 V 电源电压-最小:2.375 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LLP-24 封装:Reel |
| MPC9448D | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:3.3V/2.5V LVCMOS 1:12 Clock Fanout Buffer |
| MPC9448FA | 功能描述:时钟缓冲器 2.5 3.3V 275MHz Clock Generator RoHS:否 制造商:Texas Instruments 输出端数量:5 最大输入频率:40 MHz 传播延迟（最大值）: 电源电压-最大:3.45 V 电源电压-最小:2.375 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LLP-24 封装:Reel |
| MPC9448FAR2 | 功能描述:IC CLOCK BUFFER MUX 2:12 32-LQFP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟缓冲器，驱动器 系列:- 标准包装:1 系列:HiPerClockS™ 类型:扇出缓冲器（分配），多路复用器 电路数:1 比率 - 输入:输出:2:18 差分 - 输入:输出:是/无 输入:CML，LVCMOS，LVPECL，LVTTL，SSTL 输出:LVCMOS，LVTTL 频率 - 最大:250MHz 电源电压:2.375 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-LQFP 供应商设备封装:32-TQFP（7x7） 包装:- 其它名称:800-1923-6 |
| MPC9449 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:3.3V / 2.5 V 1:15 PECL/LVCMOS |
发布紧急采购，3分钟左右您将得到回复。