- 您现在的位置：买卖IC网 > PDF目录9028 > MPC9653AACR2 (IDT, Integrated Device Technology Inc)IC PLL CLK GEN 1:8 3.3V 32-LQFP PDF资料下载
参数资料
| 型号： | MPC9653AACR2 |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC PLL CLK GEN 1:8 3.3V 32-LQFP |
| 标准包装： | 2,000 |
| 类型： | PLL 时钟发生器 |
| PLL： | 带旁路 |
| 输入： | LVCMOS，LVPECL |
| 输出： | LVCMOS |
| 电路数： | 1 |
| 比率 - 输入:输出： | 1:8 |
| 差分 - 输入:输出： | 是/无 |
| 频率 - 最大： | 125MHz |
| 除法器/乘法器： | 是/无 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-LQFP |
| 供应商设备封装： | 32-TQFP（7x7） |
| 包装： | 带卷 (TR) |
MPC9653A REVISION 4 JANUARY 8, 2013
7
2013 Integrated Device Technology, Inc.
MPC9653A Data Sheet
3.3 V 1:8 LVCMOS PLL CLOCK GENERATOR
Calculation of Part-to-Part Skew
The MPC9653A zero delay buffer supports applications
where critical clock signal timing can be maintained across
several devices. If the reference clock inputs of two or more
MPC9653As are connected together, the maximum overall
timing uncertainty from the common PCLK input to any output
is:
tSK(PP) = t() + tSK(O) + tPD, LINE(FB) + tJIT() CF
This maximum timing uncertainty consist of 4 components:
static phase offset, output skew, feedback board trace delay
and I/O (phase) jitter:
Figure 4. MPC9653A Maximum Device-to-Device Skew
Due to the statistical nature of I/O jitter a RMS value (1
)
is specified. I/O jitter numbers for other confidence factors
(CF) can be derived from Table 8.
The feedback trace delay is determined by the board
layout and can be used to fine-tune the effective delay
through each device. In the following example calculation a
I/O jitter confidence factor of 99.7% (
3) is assumed,
resulting in a worst case timing uncertainty from input to any
output of –197 ps to 297 ps (at 125 MHz reference frequency)
relative to PCLK:
tSK(PP) = [-17ps...117ps] + [-150ps...150ps] +
[(10ps @ -3)...(10ps @ 3)] + tPD, LINE(FB)
tSK(PP) = [-197ps...297ps] + tPD, LINE(FB)
Due to the frequency dependence of the I/O jitter,
Figure 5, can be used for a more precise timing performance
analysis.
Figure 5. Maximum I/O Jitter versus Frequency
Driving Transmission Lines
The MPC9653A clock driver was designed to drive high
speed signals in a terminated transmission line environment.
To provide the optimum flexibility to the user the output
drivers were designed to exhibit the lowest impedance
possible. With an output impedance of less than 20
the
drivers can drive either parallel or series terminated
transmission lines. For more information on transmission
lines the reader is referred to Freescale Semiconductor
application note AN1091. In most high performance clock
networks point-to-point distribution of signals is the method of
choice. In a point-to-point scheme either series terminated or
parallel terminated transmission lines can be used. The
parallel technique terminates the signal at the end of the line
with a 50
resistance to VCC 2.
This technique draws a fairly high level of DC current and
thus only a single terminated line can be driven by each
output of the MPC9653A clock driver. For the series
terminated case however there is no DC current draw, thus
the outputs can drive multiple series terminated lines.
Figure 5, illustrates an output driving a single series
terminated line versus two series terminated lines in parallel.
When taken to its extreme the fanout of the MPC9653A clock
driver is effectively doubled due to its capability to drive
multiple lines.
Table 8. Confidence Factor CF
CF
Probability of clock edge within the distribution
1
0.68268948
2
0.95449988
3
0.99730007
4
0.99993663
5
0.99999943
6
0.99999999
tPD,LINE(FB)
tJIT()
+tSK(O)
—t()
+t()
tJIT()
+tSK(O)
tSK(PP)
Max. skew
PCLKCommon
QFBDevice 1
Any QDevice 1
QFBDevice2
Any QDevice 2
30
20
10
0
25 35
45
55
65
75
85
95
105 115
125
FB =
8FB = 4
3I
/O
J
itt
er
[p
s]
RMS
Reference Frequency [MHz]
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J72-MZ-F3 | CONVERTER MOD DC/DC 15V 25W |
| MPC9653AAC/W | IC PLL CLK GEN 1:8 3.3V 32-LQFP |
| VE-23F-MW-F4 | CONVERTER MOD DC/DC 72V 100W |
| VE-23F-MW-F3 | CONVERTER MOD DC/DC 72V 100W |
| VI-24T-MY-F2 | CONVERTER MOD DC/DC 6.5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MPC9653AACR2/W | 功能描述:IC PLL CLK GEN 1:8 3.3V 32-LQFP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:2,000 系列:- 类型:PLL 时钟发生器 PLL:带旁路 输入:LVCMOS，LVPECL 输出:LVCMOS 电路数:1 比率 - 输入:输出:2:11 差分 - 输入:输出:是/无 频率 - 最大:240MHz 除法器/乘法器:是/无 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-LQFP 供应商设备封装:32-TQFP（7x7） 包装:带卷 (TR) |
| MPC9653AC | 功能描述:时钟发生器及支持产品 3.3V 125MHz Clock Generator RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
| MPC9653AFA | 功能描述:时钟发生器及支持产品 3.3V 125MHz Clock Generator RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
| MPC9653AFAR2 | 功能描述:IC PLL CLK GENERATOR 1:8 32-LQFP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:39 系列:- 类型:* PLL:带旁路 输入:时钟 输出:时钟 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 频率 - 最大:170MHz 除法器/乘法器:无/无 电源电压:2.375 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| MPC9653FA | 功能描述:时钟发生器及支持产品 3.3V 125MHz Clock Generator RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
发布紧急采购，3分钟左右您将得到回复。