- 您现在的位置：买卖IC网 > PDF目录18989 > MPL115A1T2 (Freescale Semiconductor)IC BAROMETER SPI DGTL MINI 8LGA PDF资料下载
参数资料
| 型号： | MPL115A1T2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 4/16页 |
| 文件大小： | 0K |
| 描述： | IC BAROMETER SPI DGTL MINI 8LGA |
| 标准包装： | 5,000 |
| 压力类型： | 绝对 |
| 工作压力： | 7.2 PSI ~ 16.6 PSI，50 ~ 115 kPa |
| 输出： | 数字 |
| 精确度： | ±1% |
| 电源电压： | 2.375 V ~ 5.5 V |
| 端接类型： | PCB |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 8-TLGA |
3
Overview of Functions/Operation
Initial
powerup
Reading
coefficient data
Data conversion
Compensated
pressure reading
Shutdown
Figure 2. Sequence Flow Chart
The MPL115A interfaces to a host (or system) microcontroller in the user ’s application. All communications are via SPI. A typical
usage sequence is as follows:
Initial Power-up
All circuit elements are active. SPI port pins are high impedance and associated registers are cleared. The device then enters
standby mode.
Reading Coefficient Data
The user then typically accesses the part and reads the coefficient data. The main circuits within the slave device are disabled
during read activity. The coefficients are usually stored in the host microcontoller local memory but can be re-read at any time.
Reading of the coefficients may be executed only once and the values stored in the host microcontroller. It is not necessary to
read this multiple times because the coefficients within a device are constant and do not change. However, note that the
coefficients will be different from device to device, and cannot be used for another part.
Data Conversion
This is the first step that is performed each time a new pressure reading is required which is initiated by the host sending the
CONVERT command. The main system circuits are activated (wake) in response to the command and after the conversion
completes, the result is placed into the Pressure and Temperature ADC output registers.
The conversion completes within the maximum conversion time, tc (see Row 6, in the Operating Characteristics Table). The
device then enters standby mode.
Compensated Pressure Reading
After the conversion has been given sufficient time to complete, the host microcontroller reads the result from the ADC output
registers and calculates the Compensated Pressure, a barometric/atmospheric pressure value which is compensated for
changes in temperature and pressure sensor linearity. This is done using the coefficient data from the MPL115A and the raw
sampled pressure and temperature ADC output values, in a compensation equation (detailed later). Note that this is an absolute
pressure measurement with a vacuum as a reference.
From this step the host controller may either wait and then return to the Data Conversion step to obtain the next pressure reading
or it may go to the Shutdown step.
MPL115A1
Sensors
4
Freescale Semiconductor, Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| K-17-U | TOUCHSCREEN 17" USB SIDE MT |
| K-15-U | TOUCHSCREEN 15" USB SIDE MT |
| K-15-C | TOUCHSCREEN 15" RS-232 SIDE |
| E-17-C | TOUCHSCREEN 17" RS-232 |
| ASE-40.000MHZ-ET | OSC 40.000 MHZ 3.3V SMT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MPL115A2 | 功能描述:板上安装压力/力传感器 12C VERSION PEGASUS RoHS:否 制造商:Honeywell 工作压力:0 bar to 4 bar 压力类型:Gage 准确性:+ / - 0.25 % 输出类型:Digital 安装风格:Through Hole 工作电源电压:5 V 封装 / 箱体:SIP 端口类型:Dual Radial Barbed, Same sides |
| MPL115A2 | 制造商:Freescale Semiconductor 功能描述:IC MINI I2C DIGITAL BAROMETER 50 to 11 |
| MPL115A2_10 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Miniature I2C Digital Barometer |
| MPL115A2_13 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Miniature I2C Digital Barometer |
| MPL115A2T1 | 功能描述:板上安装压力/力传感器 Miniature I2C Digital Barometer RoHS:否 制造商:Honeywell 工作压力:0 bar to 4 bar 压力类型:Gage 准确性:+ / - 0.25 % 输出类型:Digital 安装风格:Through Hole 工作电源电压:5 V 封装 / 箱体:SIP 端口类型:Dual Radial Barbed, Same sides |
发布紧急采购，3分钟左右您将得到回复。