参数资料
型号: MPL115A2T1
厂商: Freescale Semiconductor
文件页数: 4/16页
文件大小: 0K
描述: IC BAROMETER I2C DGTL MINI 8-LGA
产品目录绘图: MPL115 Series Top
MPL115 Series Footprint
MPL115 Series Side
标准包装: 1
压力类型: 绝对
工作压力: 7.25 ~ 16.68 PSI,50 ~ 115 kPa
输出: SPI
精确度: ±1%
电源电压: 2.375 V ~ 5.5 V
端接类型: PCB
工作温度: -40°C ~ 105°C
封装/外壳: 8-TLGA
产品目录页面: 2808 (CN2011-ZH PDF)
其它名称: MPL115A2T1DKR
3
Overview of Functions/Operation
Initial
powerup
Reading
coefficient data
Data conversion
Compensated
pressure reading
Shutdown
Figure 2. Sequence Flow Chart
The MPL115A interfaces to a host (or system) microcontroller in the user ’s application. All communications are via I 2 C. A typical
usage sequence is as follows:
Initial Power-up
All circuit elements are active. I 2 C port pins are high impedance and associated registers are cleared. The device then enters
standby mode.
Reading Coefficient Data
The user then typically accesses the part and reads the coefficient data. The main circuits within the slave device are disabled
during read activity. The coefficients are usually stored in the host microcontoller local memory but can be re-read at any time.
It is not necessary to read the values stored in the host microcontroller multiple times because the coefficients within a device
are constant and do not change. However, note that the coefficients will be different from device to device, and cannot be used
for another part.
Data Conversion
This is the first step that is performed each time a new pressure reading is required which is initiated by the host sending the
CONVERT command. The main system circuits are activated (wake) in response to the command and after the conversion
completes, the result is placed into the Pressure and Temperature ADC output registers.
The conversion completes within the maximum conversion time, tc (see Row 7 , in the Operating Characteristics Table). The
device then enters standby mode.
Compensated Pressure Reading
After the conversion has been given sufficient time to complete, the host microcontroller reads the result from the ADC output
registers and calculates the Compensated Pressure, a barometric/atmospheric pressure value which is compensated for
changes in temperature and pressure sensor linearity. This is done using the coefficient data from the MPL115A and the raw
sampled pressure and temperature ADC output values, in a compensation equation (detailed later). Note that this is an absolute
pressure measurement with a vacuum as a reference.
From this step the host controller may either wait and then return to the Data Conversion step to obtain the next pressure reading
or it may go to the Shutdown step.
MPL115A2
Sensors
4
Freescale Semiconductor, Inc.
相关PDF资料
PDF描述
MG-75-B-MD-R SENSOR 75 PSI 4-20 MA 1/8 NPT
D2HW-BR213MR SWITCH LEVER SPST-NO 2A SEALED
MG-50-B-MD-R SENSOR 50 PSI 4-20 MA 1/8 NPT
MG-15-B-MD-R SENSOR 15 PSI 4-20 MA 1/8 NPT
MG-5-B-MD-R SENSOR 5 PSI 4-20 MA 1/8 NPT
相关代理商/技术参数
参数描述
MPL115A2T1 制造商:Freescale Semiconductor 功能描述:IC PRESSURE SENSOR I2C DIGITAL BAROMET
MPL115A2T2 功能描述:板上安装压力/力传感器 12C VERSION RoHS:否 制造商:Honeywell 工作压力:0 bar to 4 bar 压力类型:Gage 准确性:+ / - 0.25 % 输出类型:Digital 安装风格:Through Hole 工作电源电压:5 V 封装 / 箱体:SIP 端口类型:Dual Radial Barbed, Same sides
MPL1-1-61-153 制造商:Sensata Technologies 功能描述:MPL1-1-61-153 /Pole # 1 /Prod Family: 0204
MPL-12-12 功能描述:XFRMR 115/230V 5V 270MA 3OUT PCB RoHS:是 类别:变压器 >> 功率 系列:MPL 标准包装:1 系列:260 类型:标准 最大功率:65 VA 主线圈:双 副线圈:三路,中心抽头 在某电流时的串联输出电压:500 VAC @ 85mA,5 VAC @ 2A,6.3 VAC @ 2A 在某电流时的并联输出电压:- 安装类型:底座安装 尺寸/尺寸:102.36mm L x 67.31mm W 高度 - 座高(最大):66.80mm 端接类型:导线引线
MPL-12-15 功能描述:XFRMR 115/230V 5V 270MA 3OUT PCB RoHS:是 类别:变压器 >> 功率 系列:MPL 标准包装:1 系列:260 类型:标准 最大功率:65 VA 主线圈:双 副线圈:三路,中心抽头 在某电流时的串联输出电压:500 VAC @ 85mA,5 VAC @ 2A,6.3 VAC @ 2A 在某电流时的并联输出电压:- 安装类型:底座安装 尺寸/尺寸:102.36mm L x 67.31mm W 高度 - 座高(最大):66.80mm 端接类型:导线引线