- 您现在的位置：买卖IC网 > PDF目录98028 > MPQ7091 (ON SEMICONDUCTOR) 0.5 A, 150 V, 4 CHANNEL, PNP, Si, POWER TRANSISTOR, TO-116 PDF资料下载
参数资料
| 型号： | MPQ7091 |
| 厂商： | ON SEMICONDUCTOR |
| 元件分类： | 功率晶体管 |
| 英文描述： | 0.5 A, 150 V, 4 CHANNEL, PNP, Si, POWER TRANSISTOR, TO-116 |
| 封装： | PLASTIC, DIP-14 |
| 文件页数： | 22/33页 |
| 文件大小： | 310K |
| 代理商： | MPQ7091 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
Reliability and Quality Assurance
9–18
Motorola Small–Signal Transistors, FETs and Diodes Device Data
Figure 2. Impact of Assignable Causes
on Process Predictable
Figure 3. Difference Between Process
Control and Process Capability
?
Process “under control” – all assignable causes are
removed and future distribution is predictable.
PREDICTION
TIME
SIZE
TIME
PREDICTION
SIZE
TIME
Out of control
(assignable causes present)
In control assignable
causes eliminated
SIZE
TIME
In control but not capable
(variation from random variability
excessive)
Lower
Specification Limit
Upper
Specification Limit
In control and capable
(variation from random
variability reduced)
?
At Motorola, for critical parameters, the process capability
is acceptable with a Cpk = 1.50 with continual improvement
our goal. The desired process capability is a Cpk = 2 and the
ideal is a Cpk = 5. Cpk, by definition, shows where the current
production process fits with relationship to the specification
limits. Off center distributions or excessive process variability
will result in less than optimum conditions.
SPC IMPLEMENTATION AND USE
CPSTG uses many parameters that show conformance to
specification. Some parameters are sensitive to process
variations while others remain constant for a given product
line. Often, specific parameters are influenced when changes
to other parameters occur. It is both impractical and
unnecessary to monitor all parameters using SPC methods.
Only critical parameters that are sensitive to process
variability are chosen for SPC monitoring. The process steps
affecting these critical parameters must be identified as well.
It is equally important to find a measurement in these process
steps that correlates with product performance. This
measurement is called a critical process parameter.
Once the critical process parameters are selected, a
sample plan must be determined. The samples used for
measurement are organized into RATIONAL SUBGROUPS
of approximately two to five pieces. The subgroup size should
be such that variation among the samples within the subgroup
remain small. All samples must come from the same source
e.g., the same mold press operator, etc. Subgroup data should
be collected at appropriate time intervals to detect variations
in the process. As the process begins to show improved
stability, the interval may be increased. The data collected
must be carefully documented and maintained for later
correlation. Examples of common documentation entries are
operator, machine, time, settings, product type, etc.
Once the plan is established, data collection may begin. The
data collected with generate X and R values that are plotted
with respect to time. X refers to the mean of the values within
a given subgroup, while R is the range or greatest value minus
least value. When approximately 20 or more X and R values
have been generated, the average of these values is
computed as follows:
X = (X + X2 + X3 + . . .)/K
R = (R1 + R2 + R2 + . . .)/K
where K = the number of subgroups measured.
The values of X and R are used to create the process control
chart. Control charts are the primary SPC tool used to signal
a problem. Shown in Figure 4, process control charts show X
and R values with respect to time and concerning reference
to upper and lower control limit values. Control limits are
computed as follows:
R upper control limit = UCLR = D4 R
R lower control limit = LCLR = D3 R
X upper control limit = UCLX = X + A2 R
X lower control limit = LCL X = X – A2 R
相关PDF资料 |
PDF描述 |
|---|---|
| MPQ7093 | 0.5 A, 250 V, 4 CHANNEL, PNP, Si, POWER TRANSISTOR, TO-116 |
| MPS2222ZL1 | 600 mA, 30 V, NPN, Si, SMALL SIGNAL TRANSISTOR, TO-92 |
| MPS2222RL | 600 mA, 30 V, NPN, Si, SMALL SIGNAL TRANSISTOR, TO-92 |
| MPS2222RLRE | 600 mA, 30 V, NPN, Si, SMALL SIGNAL TRANSISTOR, TO-92 |
| MPS2222ARLRE | 600 mA, 40 V, NPN, Si, SMALL SIGNAL TRANSISTOR, TO-92 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MPQ7093 | 制造商:CENTRAL 制造商全称:Central Semiconductor Corp 功能描述:QUAD TRANSISTORS |
| MPQ7731DF-LF | 制造商:Monolithic Power Systems 功能描述:INDUSTRIAL GRADE, 5W-30W STEREO SE OR MONO BTL CLASS-D AUDIO - Bulk |
| MPQ7731DF-LF-Z | 制造商:Monolithic Power Systems 功能描述:INDUSTRIAL GRADE, 5W-30W STEREO SE OR MONO BTL CLASS-D AUDIO - Tape and Reel |
| MPQ8039GN-AEC1 | 功能描述:IC HALF-BRIDGE PWM 8-SOIC 制造商:monolithic power systems inc. 系列:汽车级，AEC-Q100 包装:管件 零件状态:有效 输出配置:半桥 应用:通用 接口:PWM 负载类型:电感 技术:功率 MOSFET 导通电阻（典型值）:100 毫欧 电流 - 输出/通道:4.25A 电流 - 峰值输出:9A 电压 - 电源:7.5 V ~ 24 V 电压 - 负载:7.5 V ~ 24 V 工作温度:-40°C ~ 125°C （TJ） 特性:- 故障保护:限流，超温，UVLO 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽）裸焊盘 供应商器件封装:8-SOIC-EP 标准包装:100 |
| MPQ8612GL-12-P | 功能描述:直流/直流开关转换器 12A 6V Sync Step-down Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。