参数资料
型号: MPR083QR2
厂商: Freescale Semiconductor
文件页数: 2/35页
文件大小: 0K
描述: IC CTLR TOUCH SENSOR PROX 16-QFN
产品培训模块: Sensor Toolbox
标准包装: 2,500
类型: 电容性
输入数/键: 8 个滑块
评估套件: 可供
数据接口: I²C,串行
电源电压: 1.8 V ~ 3.6 V
电流 - 电源: 1.62mA
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 16-VQFN 裸露焊盘
供应商设备封装: 16-QFN-EP(5x5)
包装: 带卷 (TR)
配用: DEMOMPR083-ND - BOARD DEMO FOR MPR083 CTLR
KITMPR083EVM-ND - KIT EVAL 8POSITION ROTARY TOUCH
MPR083
Sensors
10
Freescale Semiconductor
3
Touch Detection
3.1
Introduction
When using a capacitive touch sensor system the raw data must be filtered and interpreted. This process can be done many
different ways but the method used in the MPR083 is explained in this chapter.
3.2
Understanding the Basics
The rotary interface has to distinguish touch status through varying user conditions (different finger sizes in bare hands or gloves)
and environmental conditions (electrical and RF noise, sensor contamination with dirt or moisture).
The rotary circuitry reports touch status as one of the following two conditions:
1.
Rotary untouched
2.
Rotary touched in one of eight positions.
The rotary is only touched in one position, ideally near the middle of one of the eight pads. If a touch occurs between pads,
untouched will be reported.
3.3
Conditional Output Scenarios
Since it is unlikely that in a real world case a single independent touch will occur two specific multi-touch response cases are
outlined. Methods for changing the sensitivity of the device will be discussed in another Chapter, but the important part is that the
sensitivity is determined by the strength of an input signal. If more than one input signal is above the selected sensitivity then the
touch sensor controller interprets this in a specific way. This functionality is broken down into two different cases.
3.3.1
Simultaneous Touches
Any time two touches are detected at the same time the touch sensor controller recognizes this case and accounts for it. Any
time more than one key is pressed the touches are ignored. Thus the touch sensor controller will show the rotary as untouched.
In most cases one of the two electrodes will receive a stronger signal than the other. If the difference in capacitance is statistically
significant between the pad with the stronger signal will be reported.
This functionality is sometimes called 1-Key Lockout.
3.3.2
Sequential Touches
Another case is when one rotary pad is touched and held and a second rotary pad is then touched and held. For this situation
the second touch will be ignored and the first touch will continue to be reported.
If the second touch is released before the first touch then the second touch will be completely ignored. But, if the first touch is
released before the second then the system will report that the first key is released and that the second key is now touched. This
functionality is sometimes called 2-Key Rollover.
3.4
Rotary Configuration Register
The Rotary Configuration Register configures a variety of the MPR083 features. Each of these features is described in following
sections. The I2C slave address of the Rotary Configuration Register is 0x03.
Figure 14. Rotary Configuration Register
7
6
543210
R
RSE
00
ACE
RRBE
RTBE
0
RE
W
Reset:
1
0
000001
= Unimplemented
相关PDF资料
PDF描述
MPR084QR2 IC CTLR TOUCH SENSOR PROX 16-QFN
MPR121QR2 IC CTLR TOUCH SENSOR 20-QFN
MX674ALCWI+T IC ADC 12BIT W/REF 28-SOIC
MX7575KN+ IC ADC 8BIT MPU COMP 18-DIP
MX7582KN+ IC ADC 12BIT 4CH 28-DIP
相关代理商/技术参数
参数描述
MPR084 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Proximity Capacitive Touch Sensor Controller
MPR084EJ 功能描述:电容触摸传感器 8 POSIT 10 PADS RoHS:否 制造商:Microchip Technology 电源电压: 通道数量: 封装 / 箱体: 尺寸: 温度范围:
MPR084EJR2 功能描述:电容触摸传感器 8 POSIT 10 PADS RoHS:否 制造商:Microchip Technology 电源电压: 通道数量: 封装 / 箱体: 尺寸: 温度范围:
MPR084Q 功能描述:电容触摸传感器 4 POSITION ROTARY & RoHS:否 制造商:Microchip Technology 电源电压: 通道数量: 封装 / 箱体: 尺寸: 温度范围:
MPR084QR2 功能描述:电容触摸传感器 4 POSITION ROTARY & RoHS:否 制造商:Microchip Technology 电源电压: 通道数量: 封装 / 箱体: 尺寸: 温度范围: