- 您现在的位置：买卖IC网 > PDF目录8799 > MS17344R24C27P (Amphenol Industrial Operations)CONN PLUG 7POS STRAIGHT W/PINS PDF资料下载
参数资料
| 型号： | MS17344R24C27P |
| 厂商： | Amphenol Industrial Operations |
| 文件页数： | 23/82页 |
| 文件大小： | 0K |
| 描述： | CONN PLUG 7POS STRAIGHT W/PINS |
| 标准包装： | 1 |
| 系列： | 军用，MIL-C-22992 |
| 连接器类型： | 插头，公引脚 |
| 位置数： | 7 |
| 外壳尺寸 - 插件： | 24-27 |
| 安装类型： | 自由悬挂 |
| 端子： | 焊接 |
| 紧固型： | 有螺纹 |
| 方向： | N（正常型） |
| 外壳材料，表面处理： | 铝，导电镉镀层 |
| 触点表面涂层： | 银 |
| 包装： | 散装 |
| 电压 - 额定： | 1250VAC，1750VDC |
| 工作温度： | -55°C ~ 125°C |
| 其它名称： | MS17344R24C27P-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页
MIL-C-22992, Class L
installation instructions
Contact Installation
Step 1) Insert stripped conductors in contact wirewells.
If contact bushing is used, insert conductor in bushing
and bushing in contact wirewell. If two or more ground
wires are inserted into a single contact, make sure all
wires are fully seated in wirewell.
Connector Assembly
Step 1) If inserts are not already positioned in the con-
nector shell, align large tab on insert with large slot in
shell and push insert in until it bottoms in shell.
Step 2) Apply a thin coating of Dow Corning DC-4 lubri-
cant to the periphery of contact holes in spacer or grom-
Step 2)
Select correct crimping tool, locater and die
met assembly. Push contacts into rear of spacer or
combination from the table for contacts to be installed.
With conductor or contact bushing in place, insert contact
into tool. Close crimping die fully to form a uniform crimp.
grommet assembly until locked into contact retainer
bushing.
Step 3) Align contacts with proper holes in insert. Small
Contact
Part
Number
Size Type
Crimping
Tool*
Locator*
Die*
Removal
Tool
key of insert must be aligned with appropriate keyway in
spacer or grommet assembly. Slide contacts into insert
holes until spacer or grommet assembly butts against
M39029/48-327 4/0
P
Pico Model
insert. A thin film of Dow Corning DC-4 lubricant applied
M39029/49-335 4/0
M39029/48-328 4/0N
M39029/48-323 1/0
M39029/49-333 1/0
S
P
P
S
400B or
400B-1
Pico Model
400B or
4297-1
4297-3
414DA-4/0N-1
414DA-1/0N
MS90562-1
MS90562-3
to the periphery of insert contact holes will provide maxi-
mum sealing efficiency.
Step 4) Assemble accessories to connector. The back
M39029/48-324 1/0N
P
400B-1
adapter “O” ring should have a very thin film of Dow
M39029/48-320 4
M39029/49-331 4
M39029/48-321 4N
M39029/48-322 4G
P
S
P
P
Pico Model
400B or
400B-1
4297-5
414DA-4N
MS90562-5
Corning DC-4 lubricant applied. Outer surfaces only of
gland should be lubricated with a thin film of UniTemp
Grease EP. Avoid getting grease on inside surfaces of
M39029/49-332 4G
S
gland and on cable jacket.
M39029/48-317
M39029/49-329
M39029/48-318
6
6
6N
P
S
P
Pico Model
400B or
4297-6
414DA-6N
MS90562-6
Step 5) Tighten retaining nut or gland nut on shell or
adapter. A metal-to-metal seating condition is desireable,
M39029/48-319 6G
M39029/49-330 6G
P
S
400B-1
but may not be attainable with maximum cable diameters.
* Available from Pico Crimping Tools Co.,
9832 Jersey Ave.
Santa Fe Springs, CA 90670
Phone: 805-388-5510
If crimping tools are available, contacts may be affixed to
conductors by soldering. Use rosin-alcohol solder flux, a
good grade of 60/40 solder and a 500 watt soldering iron
or probe type resistance soldering equipment. Pre-tin
conductors before soldering. Solder must not be present
on shoulder or retention area of contact.
19
Contact Removal
Step 1) Loosen all rear accessories and slide back along
cable.
Step 2) Remove spacer or grommet assembly with con-
tacts from connector insert.
Step 3) Using the appropriate size contact removal tool,
push tool over front of contact until it bottoms in spacer or
grommet assembly hole. This will open contact retaining
bushing and allow contact to be removed from the spacer
or grommet assembly from the rear. When using jacketed
cable, all contacts should be released from contact reten-
tion bushings before removal from spacer or grommet
assembly is accomplished.
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/26JD5SCLC | CONN HSG PLUG 5POS STRGHT SCKT |
| MS27474E22F1SLC | CONN HSG RCPT 100POS JAMNUT SCKT |
| MS3456LS36-5S | CONN PLUG 4POS STRAIGHT W/SCKT |
| MS27474E22F35SLC | CONN HSG RCPT 100POS JAMNUT SCKT |
| D38999/20WJ29BA | CONN HSG RCPT 29POS WALL MT SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MS17344-R24C27P | 制造商:Amphenol Corporation 功能描述:AMPENOL CONNECTOR |
| MS17344R24C27PW | 制造商:Amphenol Corporation 功能描述:88-256624-27G - Bulk |
| MS17344R24C27PZ | 制造商:Amphenol Corporation 功能描述:88-256624-27M - Bulk |
| MS17344R24C27S | 功能描述:CONN PLUG 7POS STRAIGHT W/SCKT RoHS:否 类别:连接器，互连式 >> 圆形 系列:军用，MIL-C-22992 标准包装:1 系列:军用，MIL-C-83723 系列 III 连接器类型:插头，母型插口 位置数:12 外壳尺寸 - 插件:12-12 外壳尺寸，MIL:- 安装类型:自由悬挂 端子:压接 紧固型:插销锁 方向:9 防护等级:抗环境影响 外壳材料，表面处理:铝，镀草绿色镉 触点表面涂层:- 特点:屏蔽 包装:散装 触点涂层厚度:- 额定电流:7.5A 电压 - 额定:600VAC 工作温度:-65°C ~ 200°C 配套产品:AM83723/72W12129-ND - CONN RCPT 12POS WALL MT W/PINS 相关产品:APC1368-ND - STRAIN RELIEF STRGHT SHELL SZ 12APC1342-ND - STRAIN RLF .750-20 UNEF CADMIUMAPC1336-ND - STRAIN RELIEF 90 DEG SHELL SZ 12APC1312-ND - STRAIN RLF 90 DEG .750-20 UNEF 其它名称:M83723/77W12129-ND |
| MS17344R24C28P | 功能描述:CONN PLUG 24POS STRAIGHT W/PINS RoHS:否 类别:连接器，互连式 >> 圆形 系列:军用，MIL-C-22992 标准包装:1 系列:军用，MIL-C-83723 系列 III 连接器类型:插头，母型插口 位置数:12 外壳尺寸 - 插件:12-12 外壳尺寸，MIL:- 安装类型:自由悬挂 端子:压接 紧固型:插销锁 方向:9 防护等级:抗环境影响 外壳材料，表面处理:铝，镀草绿色镉 触点表面涂层:- 特点:屏蔽 包装:散装 触点涂层厚度:- 额定电流:7.5A 电压 - 额定:600VAC 工作温度:-65°C ~ 200°C 配套产品:AM83723/72W12129-ND - CONN RCPT 12POS WALL MT W/PINS 相关产品:APC1368-ND - STRAIN RELIEF STRGHT SHELL SZ 12APC1342-ND - STRAIN RLF .750-20 UNEF CADMIUMAPC1336-ND - STRAIN RELIEF 90 DEG SHELL SZ 12APC1312-ND - STRAIN RLF 90 DEG .750-20 UNEF 其它名称:M83723/77W12129-ND |
发布紧急采购，3分钟左右您将得到回复。