- 您现在的位置：买卖IC网 > PDF目录266232 > MS3475W22-55PW (ITT CANNON) 55 CONTACT(S), ALUMINUM ALLOY, MALE, MIL SERIES CONNECTOR, CRIMP, PLUG PDF资料下载
参数资料
| 型号： | MS3475W22-55PW |
| 厂商： | ITT CANNON |
| 元件分类： | MIL系列连接器 |
| 英文描述： | 55 CONTACT(S), ALUMINUM ALLOY, MALE, MIL SERIES CONNECTOR, CRIMP, PLUG |
| 文件页数： | 2/10页 |
| 文件大小： | 524K |
| 代理商： | MS3475W22-55PW |
www.ittcannon.com
166
Dimensions are shown in inches (millimeters).
Dimensions subject to change.
MIL-C-26482, Series 2 Connectors
PV
Assembly Procedures
STRIPPING AND CRIMPING
3/16" for
#20 CONTACT
9/32" for
#16 CONTACT
9/32" for
#12 CONTACT
Right
Wrong
CONTACT INSERTION
OPENING
COLORED END
FOR INSERTION
CONTACT EXTRACTION
COMPLETION
BROKEN CIRCLE
BREAK
1. Strip wires according to contact size: 3/16" for #20 and 9/32"for
#16 and#12. #20 contacts accommodate AWG wire sizes 20, 22, or
24; #16 accommodates 16, 18 or 20; and #12 accommodates 12 or 14.
4. Insert contact and wire into tool jaws. To crimp, squeeze handles
together fully until ratchet release and allows handles to expand;
otherwise, contact cannot be extracted from tool jaws. Maintain slight
insertion pressure on wire while crimping contact to wire.
3. Slide back tool on wire shile holding thumb against wire at opening.
Wire will slip into tool.
NOTE: Socket contacts should be inserted partially into grommet
by hand before using insertion tool.
6. Withdraw tool from rear of plug. To be sure that contact is locked,
pull back lightly on wire. Then remove tool from wire and proceed with
other contacts.
2.
Push tool into rear of plug until it bottoms. At this point, tool
releases tines on retaining clip so that contact can be extracted.
3. While maintaining slight insertion force on tool, firmly hold wire
against serrated shoulder at center of tool and extract both wired
contact and tool from plug.
4. Check face of plug or receptacle for proper contact installation. In
socket inserts with a large number of contact, cavities are identified in
a spiral pattern. A projecting line from the spiral indictates omission of a
letter; a broken circle around a cavity indicates transition between
capitals and lower case and double letters.
7. After all contacts are inserted, fill unwired cavities with sealing
plugs (insert head last and leave end protruding for ease of removal),
assemble backshell on rear of connector.
1. Remove backshell and slide back along wires to allow access. To
extract a contact, use white end of CIET tool. Place wire into tool at
large opening. Slide back tool on wire while holding thumb against wire
at opening. Wire will slip into tool.
4. With tool pressed against shoulder of contact, starting at the center
cavity, insert wired contact and tool into properly identified cavity at
rear of plug with firm, even pressure. Do not use excessive pressure.
5. When contact bottoms, a slight click can be heard as tines of metal
reataining clip snaps into place behind contact shoulder.
1. Remove backshell and put wired contacts thru cable clamp opening.
2. Used colored end of CIET tool for insertion. Place wire into tool at
large opening. To facilitate contact insertion, a 6-in. min. free lenght of
wire is recommended.
2. Insert wire into rear of contact. Wire insulation must butt against
rear of contact. Wire must be visible thru inspection hole.
3. Use M22520/1-01 crimp tool with proper crimp locator M22520/
1-02. The color code hand on the contact (red for #20, blue for #16
and yellow for #12) must match the color code of the locator and the
insertion tool throughout the crimping and assembly operations.
相关PDF资料 |
PDF描述 |
|---|---|
| MS3475W22-55SW | 55 CONTACT(S), ALUMINUM ALLOY, FEMALE, MIL SERIES CONNECTOR, CRIMP, PLUG |
| MS3475W22-55S | 55 CONTACT(S), ALUMINUM ALLOY, FEMALE, MIL SERIES CONNECTOR, CRIMP, PLUG |
| MS3475W24-19PW | 19 CONTACT(S), ALUMINUM ALLOY, MALE, MIL SERIES CONNECTOR, CRIMP, PLUG |
| MS3475W24-19PY | 19 CONTACT(S), ALUMINUM ALLOY, MALE, MIL SERIES CONNECTOR, CRIMP, PLUG |
| MS3475W22-55SW | 55 CONTACT(S), ALUMINUM ALLOY, FEMALE, MIL SERIES CONNECTOR, CRIMP, PLUG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MS3475W22-55PW-CO | 制造商:Amphenol Corporation 功能描述:CONN 26482 CIRC PIN 55 POS CRMP ST CBL MNT - Bulk 制造商:Conesys 功能描述:CONN 26482 CIRC PIN 55 POS CRMP ST CBL MNT - Bulk |
| MS3475W2255PWL | 制造商:SOURIAU 功能描述:CONN HSG PLUG 55POS STRGHT PINS |
| MS3475W22-55PWLC | 功能描述:CONN PLUG HSG MALE 55POS INLINE 制造商:amphenol aerospace operations 系列:军用，MIL-DTL-26482，系列 II 包装:散装 零件状态:在售 连接器类型:插头外壳 类型:用于公插针 针脚数:55 外壳尺寸 - 插件:22-55 外壳尺寸，MIL:- 触头类型:压接 触头尺寸:20 安装类型:自由悬挂 安装特性:- 紧固类型:插销锁 朝向:W 外壳材料:铝 外壳表面:镉 外壳颜色:草绿色 侵入防护:抗环境影响 材料可燃性等级:- 特性:连接螺母，接地 屏蔽:屏蔽 备注:不含触头 包括:- 连接螺母直径:1.656"（42.06mm） 连接螺母材料，电镀:铝，草绿色镉 嵌件材料:- 触头形状:圆形 工作温度:-65°C ~ 200°C 标准包装:1 |
| MS3475W22-55PW-LC | 功能描述:环形MIL规格连接器 55P SZ 22 PLUG CABLE MOUNT PIN RoHS:否 制造商:Amphenol MIL 类型:MIL-DTL-5015 系列:97 产品类型:Receptacles 外壳大小:28 外壳类型:Potting 触点类型:Socket (Female) 位置/触点数量:14 插入安排:28-2 触点材料:Copper Alloy 触点电镀:Silver 安装角:Straight 安装风格:Wire 端接类型:Solder 电流额定值: |
| MS3475W2255PX | 制造商:SOURIAU 功能描述:CONN PLUG 55POS STRAIGHT W/PINS |
发布紧急采购，3分钟左右您将得到回复。