参数资料
型号: MSC1200Y2PFBT
厂商: TEXAS INSTRUMENTS INC
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQFP48
封装: GREEN, PLASTIC, TQFP-48
文件页数: 16/93页
文件大小: 1093K
代理商: MSC1200Y2PFBT
MSC1200
MSC1201
MSC1202
SBAS317E APRIL 2004 REVISED MAY 2006
www.ti.com
23
ADC INPUT MULTIPLEXER
The input multiplexer provides for any combination of
differential inputs to be selected as the input channel, as
shown in Figure 8. For example, if AIN0 is selected as the
positive differential input channel, then any other channel
can be selected as the negative differential input channel.
With this method, it is possible to have up to six fully
differential input channels. It is also possible to switch the
polarity of the differential input pair to negate any offset
voltages. In addition, current sources are supplied that will
source or sink current to detect open or short circuits on the
pins.
AIN3
AIN4
AIN5
AIN0
AIN1
AIN2
AINCOM
NOTE: (1) For MSC1201/MSC1202, AIN6 and AIN7 are tied to REFIN
.
MS
C
1200
O
n
ly
BurnoutDetect(2
A)
BurnoutDetect(2
A)
AGND
Buffer
Temperature Sensor
I
80
I
AV
DD
AV
DD
AV
DD
In+
In
AIN6(1)
AIN7(1)
Figure 8. Input Multiplexer Configuration
TEMPERATURE SENSOR
On-chip diodes provide temperature sensing capability.
When the configuration register for the input mux is set to
all 1s, the diodes are connected to the inputs of the ADC.
All other channels are open. The internal device power
dissipation affects the temperature sensor reading. It is
recommended that the internal buffer be enabled for
temperature sensor measurements.
BURNOUT DETECT
When the Burnout Detect (BOD) bit is set in the ADC
control configuration register (ADCON0, SFR DCh), two
current sources are enabled. The current source on the
positive input channel sources approximately 2
A of
current. The current source on the negative input channel
sinks approximately 2
A. These current sources allow for
the detection of an open circuit (full-scale reading) or short
circuit (small differential reading) on the selected input
differential pair. The buffer should be on for sensor burnout
detection.
ADC INPUT BUFFER
The analog input impedance is always high, regardless of
PGA setting (when the buffer is enabled). With the buffer
enabled, the input voltage range is reduced and the analog
power-supply current is higher. If the limitation of input
voltage range is acceptable, then the buffer is always
preferred.
The input impedance of the MSC120x without the buffer is
7M
/PGA. The buffer is controlled by the state of the BUF
bit in the ADC control register (ADCON0, SFR DCh).
相关PDF资料
PDF描述
MC68HC11E1VFN3R2 8-BIT, 3 MHz, MICROCONTROLLER, PQCC52
MC68HC11E1VFN3 8-BIT, 3 MHz, MICROCONTROLLER, PQCC52
MC68HC705P6AVP 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP28
MSP430F5509IRGZR 16-BIT, FLASH, 25 MHz, RISC MICROCONTROLLER, PQCC48
MSP430F5510IZQE 16-BIT, FLASH, 25 MHz, RISC MICROCONTROLLER, PBGA80
相关代理商/技术参数
参数描述
MSC1200Y2PFBTG4 功能描述:模数转换器 - ADC Precision ADC & DAC w/8051 CPU & Flash RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MSC1200Y3 制造商:TI 制造商全称:Texas Instruments 功能描述:Precision Analog-to-Digital Converter (ADC) and Digital-to-Analog Converter (DAC) with 8051 Microcontroller and Flash Memory
MSC1200Y3PFBR 功能描述:模数转换器 - ADC Precision ADC & DAC w/8051 CPU & Flash RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MSC1200Y3PFBRG4 功能描述:模数转换器 - ADC Precision ADC & DAC w/8051 CPU & Flash RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MSC1200Y3PFBT 功能描述:模数转换器 - ADC Precision ADC & DAC w/8051 CPU & Flash RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32