- 您现在的位置：买卖IC网 > PDF目录365268 > MSC23836D-xxDS20 (OKI SEMICONDUCTOR CO., LTD.) HYBRID 1 POLE DIN MTG 230V 20A 24-275VAC PDF资料下载
参数资料
| 型号： | MSC23836D-xxDS20 |
| 厂商： | OKI SEMICONDUCTOR CO., LTD. |
| 英文描述： | HYBRID 1 POLE DIN MTG 230V 20A 24-275VAC |
| 中文描述： | 8388608字× 36位动态随机存储器模块：快速页面模式型 |
| 文件页数： | 9/9页 |
| 文件大小： | 52K |
| 代理商： | MSC23836D-XXDS20 |
Semconductor
MSC23836D
Notes: 1. A start-up delay of 200μs is required after power-up, followed by a minimum of eight initialization cycles
(/RAS only refresh or /CAS before /RAS refresh) before proper device operation is achieved.
2. The AC characteristics assumes t
T
= 5ns.
3. V
IH
(Min.) and V
IL
(Max.) are reference levels for measuring input timing signals. Transition time (t
T
) are
measured between V
IH
and V
IL
.
4. This parameter is measured with a load circuit equivalent to 2TTL loads and 100pF.
5. Operation within the t
RCD
(Max.) limit ensures that t
RAC
(Max.) can be met.
t
RCD
(Max.) is specified as a reference point only. If t
RCD
is greater than the specified t
RCD
(Max.) limit, then
the access time is controlled by t
CAC
.
6. Operation within the t
RAD
(Max.) limit ensures that t
RAC
(Max.) can be met.
t
RAD
(Max.) is specified as a reference point only. If t
RAD
is greater than the specified t
RAD
(Max.) limit, then
the access time is controlled by t
AA
.
7. t
OFF
(Max.) define the time at which the output achieves the open circuit condition and are not referenced
to output voltage levels.
8. t
RCH
or t
RRH
must be satisfied for a read cycle.
9. The test mode is initiated by performing a /WE and /CAS before /RAS refresh cycle. This mode is
latched and remains in effect until the exit cycle is generated. The test mode specified in this data sheet
is an 8-bit parallel test function. CA0, CA1 and CA10 are not used. In a read cycle, if all internal bits are
equal, the DQ pin will indicate a high level. If any internal bits are not equal, the DQ pin will indicate a low
level. The test mode is cleared and the memory device returned to its normal operating state by a /RAS
only refresh or /CAS before /RAS refresh cycle.
10. In a test mode read cycle, the value of access time parameters is delayed for 5ns for the specified value.
These parameters should be specified in test mode cycle by adding the above value to the specified
value in this data sheet.
相关PDF资料 |
PDF描述 |
|---|---|
| MSC23836D | 8,388,608-word x 36-bit DYNAMIC RAM MODULE : FAST PAGE MODE TYPE |
| MSC23836D-xxBS20 | 8,388,608-word x 36-bit DYNAMIC RAM MODULE : FAST PAGE MODE TYPE |
| MSC23837A-xxDS18 | SSR AS 480V 25A 0-10V |
| MSC23837A | 8,388,608-Word x 36-Bit DRAM MODULE : FAST PAGE MODE TYPE |
| MSC23837A-xxBS18 | 8,388,608-Word x 36-Bit DRAM MODULE : FAST PAGE MODE TYPE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MSC23837A | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:8,388,608-Word x 36-Bit DRAM MODULE : FAST PAGE MODE TYPE |
| MSC23837A-XXBS18 | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:8,388,608-Word x 36-Bit DRAM MODULE : FAST PAGE MODE TYPE |
| MSC23837A-XXDS18 | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:8,388,608-Word x 36-Bit DRAM MODULE : FAST PAGE MODE TYPE |
| MSC23837D | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:8,388,608-word x 36-bit DYNAMIC RAM MODULE : FAST PAGE MODE TYPE |
| MSC23837D-60BS18 | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:8,388,608-word x 36-bit DYNAMIC RAM MODULE : FAST PAGE MODE TYPE |
发布紧急采购，3分钟左右您将得到回复。