- 您现在的位置：买卖IC网 > PDF目录224503 > MSK5921KRHU (MS KENNEDY CORP) RAD TOLERANT ULTRA LOW DROPOUT ADJUSTABLE POSITIVE LINEAR REGULATOR PDF资料下载
参数资料
| 型号： | MSK5921KRHU |
| 厂商： | MS KENNEDY CORP |
| 元件分类： | 可调正电压单路输出LDO稳压器 |
| 英文描述： | RAD TOLERANT ULTRA LOW DROPOUT ADJUSTABLE POSITIVE LINEAR REGULATOR |
| 中文描述： | 1.5 V-6 V ADJUSTABLE POSITIVE LDO REGULATOR, 0.4 V DROPOUT, PSFM5 |
| 封装： | HERMETIC SEALED, SIP-5 |
| 文件页数： | 3/8页 |
| 文件大小： | 184K |
| 代理商： | MSK5921KRHU |
APPLICATION NOTES
PIN FUNCTIONS
VIN - This pin provides power to all internal circuitry
including bias, start-up, thermal limit and overcurrent
latch. Input voltage range is 2.9V to 6.5V.
GND - Internally connected to ground, this pin should be
connected externally by the user to the circuit ground.
SHUTDOWN - There are two functions to the SHUT-
DOWN pin. It may be used to disable the output voltage
or to reset a current latch condition. To activate the shut-
down/reset functions the user must apply a voltage
greater than 1.6V to the SHUTDOWN pin. The output
voltage will turn on when the SHUTDOWN pin is pulled
below the threshold voltage. If the SHUTDOWN pin is
not used, it should be connected to ground. It should be
noted that with the shutdown pin tied to ground, a cur-
rent latch condition can only be reset by cycling power
off, then on.
VOUT - This is the output pin for the device.
ADJUST - The ADJUST pin is the inverting input of the
internal error amplifier. The non-inverting input is con-
nected to an internal 1.265V reference. This error ampli-
fier controls the drive to the output transistor to force
the ADJUST pin to 1.265V. An external resistor divider
is connected to the output, ADJUST pin and ground to
set the output voltage.
CURRENT LIMIT AND SOA
The MSK 5921RH current limit function is directly af-
fected by the input and output voltages. Figure 1 illus-
trates the relationship between VIN and ICL for various
output voltages. It is very important for the user to con-
sult the SOA curve when using input voltages which
result in current limit conditions beyond 4.5 Amps. When
using input voltages which result in current limit above
4.5 Amps, the user must maintain output current within
the SOA curve to avoid damage to the device. Note that
5 Amp maximum is due to current carrying capability of
the internal wirebonds.
3
OVERCURRENT LATCH
Overcurrent protection is provided by the MSK5921RH
series through the use of a timed latch off circuit. The
internal latch timeout is triggered by an overcurrent con-
dition. To allow for start up surge currents, the timeout
is approximately 5.5mS at 25°C. If the overcurrent con-
dition remains at the end of the timeout cycle, the regu-
lator will latch off until the latch is reset. Reset the latch
by pulling the shutdown pin high or cycling VIN off then
back on. A thermal limit condition will trigger the latch
with no time out delay.
INPUT POWER SUPPLY BYPASSING
To maximize transient response and minimize power
supply transients it is recommended that a 100μF tanta-
lum capacitor is connected between VIN and ground. A
0.1μF ceramic capacitor should also be used for high
frequency bypassing.
FIGURE 1
Rev. L 1/11
OUTPUT CAPACITOR SELECTION
Low ESR output capacitors are required to maintain regu-
lation and stability. Four CWR29FB227 (AVX PN
TAZH227K010L) tantalum capacitors in parallel with ce-
ramic decoupling capacitors (0.1μF typical) provides suf-
ficient gain and phase margin for most applications. The
maximum ESR specification for the CWR29FB227 capaci-
tor is 180mΩ at 100kHz and is sufficient for many appli-
cations. MSK has found through full WCCA that screen-
ing for a maximum ESR of 57mΩ ensures EOL stability
criteria to be met for many applications with the most
stringent requirements. The typical ESR of the
TAZH227K010L from AVX is 49mΩ . Analysis of the final
design is recommended to ensure stability requirements
are met.
相关PDF资料 |
PDF描述 |
|---|---|
| MSK604B | NEGATIVE OUTPUT WIDE BANDWIDTH HIGH VOLTAGE AMPLIFIER |
| MSK613H | HIGH VOLTAGE/HIGH SPEED SURFACE MOUNT AMPLIFIER |
| MSK641B | WIDE BANDWIDTH, VERY HIGH VOLTAGE CRT VIDEO AMPLIFIER |
| MSK642B | WIDE BANDWIDTH, HIGH VOLTAGE CRT VIDEO AMPLIFIER |
| MSK643B | WIDE BANDWIDTH, VERY HIGH VOLTAGE CRT VIDEO AMPLIFIER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MSK600 | 制造商:MSK 制造商全称:M.S. Kennedy Corporation 功能描述:WIDE BANDWIDTH HIGH VOLTAGE AMPLIFIER |
| MSK601 | 制造商:MSK 制造商全称:M.S. Kennedy Corporation 功能描述:WIDE BANDWIDTH HIGH VOLTAGE AMPLIFIER |
| MSK601B | 制造商:MSK 制造商全称:M.S. Kennedy Corporation 功能描述:WIDE BANDWIDTH HIGH VOLTAGE AMPLIFIER |
| MSK604 | 制造商:MSK 制造商全称:M.S. Kennedy Corporation 功能描述:NEGATIVE OUTPUT WIDE BANDWIDTH HIGH VOLTAGE AMPLIFIER |
| MSK604B | 制造商:MSK 制造商全称:M.S. Kennedy Corporation 功能描述:NEGATIVE OUTPUT WIDE BANDWIDTH HIGH VOLTAGE AMPLIFIER |
发布紧急采购，3分钟左右您将得到回复。