- 您现在的位置：买卖IC网 > PDF目录224503 > MSK641B (MS KENNEDY CORP) WIDE BANDWIDTH, VERY HIGH VOLTAGE CRT VIDEO AMPLIFIER PDF资料下载
参数资料
| 型号： | MSK641B |
| 厂商： | MS KENNEDY CORP |
| 元件分类： | 音频／视频放大 |
| 英文描述： | WIDE BANDWIDTH, VERY HIGH VOLTAGE CRT VIDEO AMPLIFIER |
| 中文描述： | 1 CHANNEL, VIDEO AMPLIFIER, BFM9 |
| 封装： | HEAT SINK, SIP-9 |
| 文件页数： | 3/6页 |
| 文件大小： | 284K |
| 代理商： | MSK641B |
TYPICAL TEST CIRCUIT
The signal source in Figure 1 can be either a fast pulse gen-
erator or a network analyzer as long as the output impedance is
50 ohms. The DC level of the input should be 1.55V and all
cables should be kept as short as possible. Since total load
capacitance should be kept below 8.5pF, a FET probe should
be used on the ouput.
USING THE MSK 641
The output of the amplifier is biased at one half of the power
supply voltage. An output voltage swing of ±35 volts is typi-
cal with a power supply voltage of +80 volts. With an 8.5pF
capacitive load, transistion times are in the 2.5nS range. If a
spark gap current limiting resistor is used on the output of the
amplifier and the transistion times are degraded, a peaking coil
may be used to preserve system performance. The optimum
value for this coil will be in the range of 100 to 200nH and can
best be determined by trial and error. The output of the MSK
641 is not short circuit protected, therefore, purely resistive
loads should be no less than 800 ohms at any time to avoid
damaging the output.
OPERATION CONSIDERATIONS
The input of the MSK 641 rests at a +1.55VDC level with
Vcc=+80VDC and the input terminal open. In this state, the
output rests at one half of the power supply voltage. When
connecting a pulse generator to the input of the amplifier, the
DC level should be offset so that the signal is centered around
+1.55V. During characterization, the input should be coupled
to the MSK 641 through a parallel combination of a variable
resistor and variable capacitor peaking circuit. Optimum values
for the peaking circuit can be determined experimentally. The
optimum value of load capacitance is 8.5pF. Viewing the out-
put with a normal oscilloscope probe would seriously degrade
performance. A FET probe fitted with a 100:1 voltage divider
will add only approximately 1.5pF of capacitance to the load
and is highly recommended. An experimental circuit along with
recommended values can be found in Figure 2.
APPLICATION NOTES
OUTPUT ISSUES
The output of the MSK 641 is a pair of bipolar emitter follow-
ers configured in a complimentary push pull configuration. This
configuration eliminates the need for a pull up load resistor and
makes the amplifier less susceptible to load capacitance varia-
tions. Connecting a wire or cable from the output of the ampli-
fier to the CRT cathode can create a resonant circuit which can
cause unwanted oscillations or overshoot at its resonant fre-
quency. A damping resistor in series with the lead inductance
will alleviate this condition. The optimum value of this resistor
can be determined using the following formula:
R = 2*
√L/C
This resistor also doubles as an arcing protector. In the bread-
boarding stage, the value of this resistor should be determined
experimentally. Resistance in the range of 50 to 100 ohms is
usually sufficient.
If a quick, simple peaking network is de-
sired, a 300 ohm cable terminated by a capacitor will act like an
inductor in the frequency range involved.
HEAT SINKING
The MSK 641 requires heat sinking in most applications. The
following formula may be applied to determine if a heat sink is
necessary and what size and type to use.
Rθsa = ((Tj-Ta)/Pd ) - (Rθjc) - (Rθcs)
WHERE
Tj = Junction Temperature
Pd = Total power dissipation
Rθjc = Junction to case thermal resistance
Rθcs = Case to heat sink thermal resistance
Rθsa = Heat sink to ambient thermal resistance
Tc = Case temperature
Ta = Ambient temperature
Ts = Sink temperature
EXAMPLE
Tj = 150°C
Ta = 100°C
Pd = 1.5W
Rθjc = 27°C/W
Rθcs = 0.15°C/W
Solving the above equation for Rθsa (heat sink thermal conduc-
tivity) shows that the heat sink for this application must have a
thermal resistance of no more than 6.0°C/W to maintain a junc-
tion temperature of no more than 150°C.
TRANSIMPEDANCE AMPLIFICATION
Transimpedance amplifiers relate input current to output volt-
age. The MSK 641 contains an internal 4K
feedback resistor.
This resistor converts input current to output voltage in the
following manner (See Figure 1):
±1.43V (referenced to 1.55Vdc) across the 300
input re-
sistor results in an input current of ±4.77mA. This current
flows through the 4K
feedback resistor and results approxi-
mately in a ±20V swing at the output. The actual voltage gain
of the typical MSK641 circuit may be slightly less due to tran-
sistor losses. The following formula approximates voltage gain
including potential losses:
Voltage Gain (V/V) = 4K
/(Rin + L)
L
≈ 25
Rev. F 10/05
3
相关PDF资料 |
PDF描述 |
|---|---|
| MSK642B | WIDE BANDWIDTH, HIGH VOLTAGE CRT VIDEO AMPLIFIER |
| MSK643B | WIDE BANDWIDTH, VERY HIGH VOLTAGE CRT VIDEO AMPLIFIER |
| MSK645B | HIGH PERFORMANCE, HIGH VOLTAGE VIDEO DISPLAY DRIVER |
| MSL400C-NKB6HD | SINGLE COLOR LED, BLUE |
| MS400-NWW28H | SINGLE COLOR LED, COOL WHITE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MSK642 | 制造商:MSK 制造商全称:M.S. Kennedy Corporation 功能描述:WIDE BANDWIDTH, HIGH VOLTAGE CRT VIDEO AMPLIFIER |
| MSK642B | 制造商:MSK 制造商全称:M.S. Kennedy Corporation 功能描述:WIDE BANDWIDTH, HIGH VOLTAGE CRT VIDEO AMPLIFIER |
| MSK643 | 制造商:MSK 制造商全称:M.S. Kennedy Corporation 功能描述:WIDE BANDWIDTH, VERY HIGH VOLTAGE CRT VIDEO AMPLIFIER |
| MSK643B | 制造商:MSK 制造商全称:M.S. Kennedy Corporation 功能描述:WIDE BANDWIDTH, VERY HIGH VOLTAGE CRT VIDEO AMPLIFIER |
| MSK645 | 制造商:MSK 制造商全称:M.S. Kennedy Corporation 功能描述:HIGH PERFORMANCE, HIGH VOLTAGE VIDEO DISPLAY DRIVER |
发布紧急采购，3分钟左右您将得到回复。