- 您现在的位置：买卖IC网 > PDF目录132979 > MSM6665C-XXGS-K (LAPIS SEMICONDUCTOR CO LTD) 16 X 80 DOTS DOT MAT LCD DRVR AND DSPL CTLR, PQFP128 PDF资料下载
参数资料
| 型号： | MSM6665C-XXGS-K |
| 厂商： | LAPIS SEMICONDUCTOR CO LTD |
| 元件分类： | 显示控制器 |
| 英文描述： | 16 X 80 DOTS DOT MAT LCD DRVR AND DSPL CTLR, PQFP128 |
| 封装： | 14 X 20 MM, 0.50 MM PITCH, PLASTIC, QFP-128 |
| 文件页数： | 6/33页 |
| 文件大小： | 623K |
| 代理商： | MSM6665C-XXGS-K |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
13/32
OKI Semiconductor
MSM6665C-xx
DISP (Display on/off)
[1,0,0,X,1,0,0,1/0]
Command used to control display-on and display-off of the LCD panel.
When D0 is "1", the display of the LCD panel goes on, and When D0 is "0", it goes off.
When the display is off, the VDD level voltage is output on all of pins of both the segment
drivers and the common drivers.
D0 is set to "0" after inputting Reset.
ABBC 1/5 (Arbitrator Blink Control 1/5 dot)
[1,0,0,1,1,1,0,1/0]
Command used to do switching between arbitrator’s blinking in a 1-dot unit and or in
a 5-dot unit.
When D0 is "1", arbitrator’s blinking comes in the 1 dot unit mode.
When D0 is "0", it comes in the 5-dot unit mode.
D0="0" is set after inputting Reset.
Note: 1-dot unit blink setting See ABB.
5-dot unit blink setting See CHB.
ABB (Arbitrator Blink)
[1,0,0,0,1,1,0,1/0]
Command used to control on/off of blinking, which is valid only when arbitrator’s
blinking is set in the 1-dot unit mode.
Data , which are entered via SI pin after setting D0="1", are taken as arbitrator blink data
(1-dot unit).
Input blink data correspond to each of arbitrator’s dots. When "1", blinking is on, and
when "0", blinking is off.
Note that the arbitrator, which arbitrator-on is not specified, is not able to blink, though
blink-setting is available. Dummy data must be entered into the arbitrator blink data D5
thru D7.
It is impossible to write data in addresses 00 through 31.
D0="0" is set after inputting Reset.
Note: If blink is set in the 5-dot unit mode, ABB command setting (D0="1" or "0") is
available, but blink-on/off setting via input of display data is impossible.
AINC (Address Increment)
[1,0,0,X,1,X,1,X]
Command used to increment the value of the address pointer by 1.
The pointer is increment by 1 each time this command is executed. The operation set by
LOT command is given to the address before being increased by 1 each time this
command is execution.
相关PDF资料 |
PDF描述 |
|---|---|
| MPC5607BCLQ4 | FLASH, 48 MHz, MICROCONTROLLER, PQFP144 |
| MPC5607BCLQ6 | FLASH, 64 MHz, MICROCONTROLLER, PQFP144 |
| MPC5607BCLU4 | FLASH, 48 MHz, MICROCONTROLLER, PQFP176 |
| MPC5607BCLU6R | FLASH, 64 MHz, MICROCONTROLLER, PQFP176 |
| MPC5607BCLU6 | FLASH, 64 MHz, MICROCONTROLLER, PQFP176 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MSM6665-XX | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:DOT MATRIX LCD CONTROLLER WITH 17-DOT COMMON DRIVER AND 80-DOT SEGMENT DRIVER |
| MSM6669 | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:80-DOT LCD SEGMENT DRIVER |
| MSM6679A-110 | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:SI/SD Voice Recognizer, Recorder/Player, and Speech Synthesizer |
| MSM6679AL-110 | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:SI/SD Voice Recognizer, Recorder/Player, and Speech Synthesizer |
| MSM6684B | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:4,194,304-word x 1-bit Serial Register |
发布紧急采购，3分钟左右您将得到回复。