- 您现在的位置：买卖IC网 > PDF目录299521 > MSM9225 (OKI SEMICONDUCTOR CO., LTD.) CAN (Controller Area Network) Controller PDF资料下载
参数资料
| 型号： | MSM9225 |
| 厂商： | OKI SEMICONDUCTOR CO., LTD. |
| 英文描述： | CAN (Controller Area Network) Controller |
| 中文描述： | CAN（控制器局域网）控制器 |
| 文件页数： | 6/74页 |
| 文件大小： | 488K |
| 代理商： | MSM9225 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页
Semiconductor
MSM9225
14/73
(4) CAN write flag: CANA
This bit is used to indicate receive data write status to the message memory. CANA is
"1" while CAN is writing receive data to the message memory.
This is a read-only flag.
(5) Transmission flag: TxF
This bit is used to indicate transmission operation status.
When TxF is "0", CAN is in transmission operation stop status.
When TxF is "1", CAN is in transmission operation status. TxF becomes "0" when
transmission completes.
This is a read-only flag.
(6) Receive flag: RxF
This bit is used to indicate receive operation status.
When RxF is "0", CAN is in receive operation stop status.
When RxF is "1", CAN is in receive operation status. RxF becomes "0" when receiving
completes.
This is a read-only flag.
2. CAN interrupt register (CANI: 0Fhex)
This register controls CAN interrupts.
The bit configuration is as follows:
(1) Transmission interrupt output enable: EINTT
This bit is used to output transmission interrupt signal INTT from interrupt pin INT
when transmission completes.
When EINTT is "0", a transmission interrupt signal is not output from the interrupt pin.
When EINTT is "1", a transmission interrupt signal is output from the interrupt pin.
At reset, EINTT is set to "0".
(2) Receive interrupt output enable: EINTR
This bit is used to output receive interrupt signal INTR from interrupt pin INT when
reception completes.
When EINTR is "0", a receive interrupt signal is not output from the interrupt pin.
When EINTR is "1", a receive interrupt signal is output from the interrupt pin.
At reset, EINTR is set to "0".
76543210
Address MSB
0Fh
LSB
EINTT
: Transmission interrupt output enable
EINTR : Receive interrupt output enable
EINTE : Error interrupt output enable
Not used
ITF
: Transmission interrupt request flag
IRF
: Receive interrupt request flag
IEF
: Error interrupt request flag
MEINT : Master interrupt control enable
相关PDF资料 |
PDF描述 |
|---|---|
| MSMP3V-E3/89A | 100 W, UNIDIRECTIONAL, SILICON, TVS DIODE |
| MSO2TM-1.5MHZ | CRYSTAL OSCILLATOR, CLOCK, 1.5 MHz, TTL OUTPUT |
| MSO2C-40MHZ | CRYSTAL OSCILLATOR, CLOCK, 40 MHz, CMOS OUTPUT |
| MSO2C-FREQ | CRYSTAL OSCILLATOR, CLOCK, 1.5 MHz - 40 MHz, CMOS OUTPUT |
| MSO2T-40MHZ | CRYSTAL OSCILLATOR, CLOCK, 40 MHz, TTL OUTPUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MSM9225B | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:CAN (Controller Area Network) Controller |
| MSM9225BGA | 制造商:ROHM Semiconductor 功能描述: |
| MSM9225BGA-2K | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:CAN (Controller Area Network) Controller |
| MSM9225BGAZ020 | 制造商:ROHM Semiconductor 功能描述: |
| MSM9225BGAZ0VL | 制造商:ROHM Semiconductor 功能描述: |
发布紧急采购，3分钟左右您将得到回复。