- 您现在的位置：买卖IC网 > PDF目录68018 > MSP430A002IPMR (TEXAS INSTRUMENTS INC) 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | MSP430A002IPMR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQFP64 |
| 封装： | GREEN, PLASTIC, LQFP-64 |
| 文件页数： | 33/62页 |
| 文件大小： | 1007K |
| 代理商： | MSP430A002IPMR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
MSP430x13x, MSP430x14x, MSP430x14x1
MIXED SIGNAL MICROCONTROLLER
SLAS272F JULY 2000 REVISED JUNE 2004
39
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
electrical characteristics over recommended operating free-air temperature (unless otherwise
noted) (continued)
Flash Memory
PARAMETER
TEST
CONDITIONS
VCC
MIN
NOM
MAX
UNIT
VCC(PGM/
ERASE)
Program and Erase supply voltage
2.7
3.6
V
fFTG
Flash Timing Generator frequency
257
476
kHz
IPGM
Supply current from DVCC during program
2.7 V/ 3.6 V
3
5
mA
IERASE
Supply current from DVCC during erase
2.7 V/ 3.6 V
3
7
mA
tCPT
Cumulative program time
see Note 1
2.7 V/ 3.6 V
4
ms
tCMErase
Cumulative mass erase time
see Note 2
2.7 V/ 3.6 V
200
ms
Program/Erase endurance
104
105
cycles
tRetention
Data retention duration
TJ = 25°C
100
years
tWord
Word or byte program time
35
tBlock, 0
Block program time for 1st byte or word
30
tBlock, 1-63
Block program time for each additional byte or word
see Note 3
21
tFTG
tBlock, End
Block program end-sequence wait time
see Note 3
6
tFTG
tMass Erase
Mass erase time
5297
tSeg Erase
Segment erase time
4819
NOTES:
1. The cumulative program time must not be exceeded when writing to a 64-byte flash block. This parameter applies to all programming
methods: individual word/byte write and block write modes.
2. The mass erase duration generated by the flash timing generator is at least 11.1ms ( = 5297x1/fFTG,max = 5297x1/476kHz). To
achieve the required cumulative mass erase time the Flash Controller’s mass erase operation can be repeated until this time is met.
(A worst case minimum of 19 cycles are required).
3. These values are hardwired into the Flash Controller’s state machine (tFTG = 1/fFTG).
JTAG Interface
PARAMETER
TEST
CONDITIONS
VCC
MIN
NOM
MAX
UNIT
fTCK
TCK input frequency
see Note 1
2.2 V
0
5
MHz
fTCK
TCK input frequency
see Note 1
3 V
0
10
MHz
RInternal
Internal pull-up resistance on TMS, TCK, TDI/TCLK
see Note 2
2.2 V/ 3 V
25
60
90
k
NOTES:
1. fTCK may be restricted to meet the timing requirements of the module selected.
2. TMS, TDI/TCLK, and TCK pull-up resistors are implemented in all versions.
JTAG Fuse (see Note 1)
PARAMETER
TEST
CONDITIONS
VCC
MIN
NOM
MAX
UNIT
VCC(FB)
Supply voltage during fuse-blow condition
TA = 25°C
2.5
V
VFB
Voltage level on TDI/TCLK for fuse-blow: F versions
6
7
V
IFB
Supply current into TDI/TCLK during fuse blow
100
mA
tFB
Time to blow fuse
1
ms
NOTES:
1. Once the fuse is blown, no further access to the MSP430 JTAG/Test and emulation features is possible. The JTAG block is switched
to bypass mode.
相关PDF资料 |
PDF描述 |
|---|---|
| MSP430A006IRTDR | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQCC64 |
| MSP430A006IPWR | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQFP64 |
| MSP430A007IRTDR | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQCC64 |
| MSP430A007IPMR | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQFP64 |
| MSP430A015IPMR | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MSP430A003IPWR | 制造商:TI 制造商全称:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER |
| MSP430A004IPW | 制造商:TI 制造商全称:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER |
| MSP430A004IPWR | 制造商:Texas Instruments 功能描述: |
| MSP430A005IPW | 制造商:TI 制造商全称:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER |
| MSP430A005IPWR | 制造商:TI 制造商全称:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER |
发布紧急采购，3分钟左右您将得到回复。