- 您现在的位置：买卖IC网 > PDF目录80495 > MSP430F1111AIDWR (TEXAS INSTRUMENTS INC) 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PDSO20 PDF资料下载
参数资料
| 型号： | MSP430F1111AIDWR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PDSO20 |
| 封装： | GREEN, PLASTIC, SOIC-20 |
| 文件页数： | 26/43页 |
| 文件大小： | 869K |
| 代理商： | MSP430F1111AIDWR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
MSP430C11x1, MSP430F11x1A
MIXED SIGNAL MICROCONTROLLER
SLAS241I SEPTEMBER 1999 REVISED DECEMBER 2008
32
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
JTAG fuse check mode
MSP430 devices that have the fuse on the TEST terminal have a fuse check mode that tests the continuity of
the fuse the first time the JTAG port is accessed after a power-on reset (POR). When activated, a fuse check
current, ITF, of 1 mA at 3 V, 2.5 mA at 5 V can flow from the TEST pin to ground if the fuse is not burned. Care
must be taken to avoid accidentally activating the fuse check mode and increasing overall system power
consumption.
When the TEST pin is taken back low after a test or programming session, the fuse check mode and sense
currents are terminated.
Activation of the fuse check mode occurs with the first negative edge on the TMS pin after power up or if TMS
is being held low during power up. The second positive edge on the TMS pin deactivates the fuse check mode.
After deactivation, the fuse check mode remains inactive until another POR occurs. After each POR the fuse
check mode has the potential to be activated.
The fuse check current will only flow when the fuse check mode is active and the TMS pin is in a low state (see
Figure 13). Therefore, the additional current flow can be prevented by holding the TMS pin high (default
condition).
Time TMS Goes Low After POR
TMS
ITF
ITEST
Figure 13. Fuse Check Mode Current, MSP430F11x1A and MSP430C11x1
NOTE:
The CODE and RAM data protection is ensured if the JTAG fuse is blown and the 256-bit bootloader
access key is used. Also, see the bootstrap loader section for more information.
相关PDF资料 |
PDF描述 |
|---|---|
| M30302MCL-XXXGP | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| MB89191AHP | 8-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PDIP28 |
| MB90455PMT | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP48 |
| MB90456SPMT | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP48 |
| MB90F462PFM | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MSP430F1111AIPW | 功能描述:16位微控制器 - MCU 2kB Flash 128B RAM Comparator RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| MSP430F1111AIPW | 制造商:Texas Instruments 功能描述:16-Bit Microcontroller IC |
| MSP430F1111AIPWR | 功能描述:16位微控制器 - MCU 2kB Flash 128B RAM Comparator RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| MSP430F1111AIRGE | 制造商:TI 制造商全称:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER |
| MSP430F1111AIRGER | 功能描述:16位微控制器 - MCU 2kB Flash 128B RAM Comparator RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。