参数资料
型号: MTCBA-C1-N2
厂商: Multi-Tech Systems
文件页数: 104/135页
文件大小: 0K
描述: MODEM CDMA RS232 DUAL
标准包装: 10
系列: MultiModem® Cell
功能: 收发器,CDMA,调制解调器
调制或协议: CDMA2000
频率: 800MHz,1.9GHz
应用: Sprint 网络(USA)
接口: RS-232
数据传输率 - 最大: 153.6 kbps
电源电压: 9 V ~ 32 V
其它名称: 881-1147
Chapter 17 – TCP APP AT Commands
Socket Data Exchange +WIPDATA
Description :
The +WIPDATA command is used to read from or write to a socket. On successful execution of
the command, the UART switches to online data mode. The UART can be switched back to
online command mode (AT mode with PPP data call established) by sending an escape
sequence (“+++”) within a 1 second guard time before and after the sequence. De-asserting DTR
can also switch the mode from Data mode to Online Command mode (depending on the &D
setting). If data is not read using +WIPDATA command, further data will be delayed.
Syntax:
Command syntax:
Command
AT+WIPDATA=<protocol>,<index>,<mode>
Possible Responses
AT+WIPDATA=<protocol>,<index>,<mode> CONNECT
AT+WIPDATA=? OK
AT+WIPDATA?
OK
or displays pending data in socket as follows:
Note: if <protocol> equals 1:
+WIPDATA: <protocol>,<index>,<datagram
size>,<peer IP>,<peer port>
Note: if <protocol> equals 2:
+WIPDATA: <protocol>,<index>,<number of
readable bytes>
Values:
<protocol>
1
2
<index>
1-8
<mode>
1
2
UDP
TCP client
Socket or session identifier
Mode of operation.
Continuous Mode
Data mode used by UDP sockets. Data is collected from UART until the [ETX]
character is encountered in the data stream, or until the maximum size of the buffer is
reached, then sent as a single datagram. If the [ETX] character needs to be
transmitted then it must be preceded by the [DLE] character. This mode is only
supported by UDP protocol.
Continuous Transparent Mode
Data mode used by TCP sockets. All data received on UART is treated as data. In
this mode, [DLE]/[ETX] characters are considered as normal data and not special
characters. This mode is only supported for TCP protocol.
+WIPDATA Unsolicited Response:
The +WIPDATA unsolicited response is output when data is received on a given
socket while in Online Command mode. If data is not read using +WIPDATA
command, further data will be delayed and +WIPDATA will not be shown.
Multi-Tech Systems, Inc. CDMA C1 AT Commands Reference Guide (PN S000478C)
104
相关PDF资料
PDF描述
MTCBA-EV2-EN2-N16 ROUTER WIRELESS EV-DO DUAL
MTCMR-H4-P1-EU MODEM CELLULAR QUAD GPRS HSPA
MTCMR-EV2-N2-NAM MODEM CELLULAR EV-DO DUAL
EFG15F MODULE DIODE 170A 480VAC
MTCMR-H4-P1-GB/IE MODEM CELLULAR QUAD GPRS HSPA
相关代理商/技术参数
参数描述
MTCBA-C1-N2-NAM 功能描述:MODEM CELLULAR RS232 DUAL CDMA RoHS:是 类别:RF/IF 和 RFID >> RF 接收器、发射器及收发器的成品装置 系列:MultiModem® Cell 标准包装:5 系列:MultiModem® iCell 功能:收发器,HSPA,调制解调器 调制或协议:GPRS,GSM,EDGE 频率:850MHz,900MHz,1.8GHz,1.9GHz 应用:- 接口:RS-232,USB 灵敏度:- 功率 - 输出:- 数据传输率 - 最大:7.2 Mbps 特点:- 电源电压:9 V ~ 32 V,USB 其它名称:881-1125
MTCBA-C1-N3 功能描述:MODEM CDMA RS232 DUAL RoHS:是 类别:RF/IF 和 RFID >> RF 接收器、发射器及收发器的成品装置 系列:MultiModem® Cell 标准包装:5 系列:MultiModem® iCell 功能:收发器,HSPA,调制解调器 调制或协议:GPRS,GSM,EDGE 频率:850MHz,900MHz,1.8GHz,1.9GHz 应用:- 接口:RS-232,USB 灵敏度:- 功率 - 输出:- 数据传输率 - 最大:7.2 Mbps 特点:- 电源电压:9 V ~ 32 V,USB 其它名称:881-1125
MTCBA-C1-N3-NAM 功能描述:MODEM CELLULAR RS232 DUAL CDMA RoHS:是 类别:RF/IF 和 RFID >> RF 接收器、发射器及收发器的成品装置 系列:MultiModem® Cell 标准包装:5 系列:MultiModem® iCell 功能:收发器,HSPA,调制解调器 调制或协议:GPRS,GSM,EDGE 频率:850MHz,900MHz,1.8GHz,1.9GHz 应用:- 接口:RS-232,USB 灵敏度:- 功率 - 输出:- 数据传输率 - 最大:7.2 Mbps 特点:- 电源电压:9 V ~ 32 V,USB 其它名称:881-1125
MTCBA-C1-U-N2 功能描述:MODEM CDMA USB 800MHZ 1.9GHZ RoHS:是 类别:RF/IF 和 RFID >> RF 接收器、发射器及收发器的成品装置 系列:MultiModem® Cell 标准包装:5 系列:MultiModem® iCell 功能:收发器,HSPA,调制解调器 调制或协议:GPRS,GSM,EDGE 频率:850MHz,900MHz,1.8GHz,1.9GHz 应用:- 接口:RS-232,USB 灵敏度:- 功率 - 输出:- 数据传输率 - 最大:7.2 Mbps 特点:- 电源电压:9 V ~ 32 V,USB 其它名称:881-1125
MTCBA-C1-U-N3 功能描述:MODEM CDMA USB 800MHZ 1.9GHZ RoHS:是 类别:RF/IF 和 RFID >> RF 接收器、发射器及收发器的成品装置 系列:MultiModem® Cell 标准包装:5 系列:MultiModem® iCell 功能:收发器,HSPA,调制解调器 调制或协议:GPRS,GSM,EDGE 频率:850MHz,900MHz,1.8GHz,1.9GHz 应用:- 接口:RS-232,USB 灵敏度:- 功率 - 输出:- 数据传输率 - 最大:7.2 Mbps 特点:- 电源电压:9 V ~ 32 V,USB 其它名称:881-1125