收藏本站
参数资料
型号： MV80C51T-16D
厂商： ATMEL CORP
元件分类： 微控制器/微处理器
英文描述： 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44
封装： 1.40 MM HEIGHT, QFP-44
文件页数： 101/170页
文件大小： 4133K
代理商： MV80C51T-16D
36
ATtiny4/5/9/10 [DATASHEET]
8127F–AVR–02/2013
0x000B
RESET: ldi
r16, high(RAMEND); Main program start
0x000C
out
SPH,r16
; Set Stack Pointer
0x000D
ldi
r16, low(RAMEND) ; to top of RAM
0x000E
out
SPL,r16
0x000F
sei
; Enable interrupts
0x0010
<instr>
...
9.2
External Interrupts
External Interrupts are triggered by the INT0 pin or any of the PCINT3..0 pins. Observe that, if enabled, the inter-
rupts will trigger even if the INT0 or PCINT3..0 pins are configured as outputs. This feature provides a way of
generating a software interrupt. Pin change 0 interrupts PCI0 will trigger if any enabled PCINT3..0 pin toggles. The
PCMSK Register controls which pins contribute to the pin change interrupts. Pin change interrupts on PCINT3..0
are detected asynchronously, which means that these interrupts can be used for waking the part also from sleep
modes other than Idle mode.
The INT0 interrupt can be triggered by a falling or rising edge or a low level. This is set up as shown in “EICRA –
External Interrupt Control Register A” on page 37. When the INT0 interrupt is enabled and configured as level trig-
gered, the interrupt will trigger as long as the pin is held low. Note that recognition of falling or rising edge interrupts
on INT0 requires the presence of an I/O clock, as described in “Clock System” on page 17.
9.2.1
Low Level Interrupt
A low level interrupt on INT0 is detected asynchronously. This means that the interrupt source can be used for
waking the part also from sleep modes other than Idle (the I/O clock is halted in all sleep modes except Idle).
Note that if a level triggered interrupt is used for wake-up from Power-down, the required level must be held long
enough for the MCU to complete the wake-up to trigger the level interrupt. If the level disappears before the end of
the Start-up Time, the MCU will still wake up, but no interrupt will be generated. The start-up time is defined as
described in “Clock System” on page 17.
If the low level on the interrupt pin is removed before the device has woken up then program execution will not be
diverted to the interrupt service routine but continue from the instruction following the SLEEP command.
9.2.2
Pin Change Interrupt Timing
A timing example of a pin change interrupt is shown in Figure 9-1.
相关PDF资料
PDF描述
MP80C31-30D 8-BIT, 30 MHz, MICROCONTROLLER, PDIP40
MT80C31-25D 8-BIT, 25 MHz, MICROCONTROLLER, PQFP44
MS80C31-20D 8-BIT, 20 MHz, MICROCONTROLLER, PQCC44
MS80C51T-20D 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQCC44
MT80C51T-20R 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP44
相关代理商/技术参数
参数描述
MV8102 功能描述:标准LED-通孔 T-1 3/4 RED CLR 20DG RoHS:否 制造商:Vishay Semiconductors 照明颜色:Red 光强度:0.7 mcd 波长/色温:615 nm 显示角:45 deg 透镜颜色/类型:Clear, Non-Diffused 正向电流:70 mA 正向电压:1.83 V to 3.03 V LED 大小:2 mm 系列: 封装:Tube
MV8102 制造商:Fairchild Semiconductor Corporation 功能描述:LED ALGAAS SUPERBRIGHT RED
MV8102 制造商:Fairchild Semiconductor Corporation 功能描述:LED LAMP
MV8103 功能描述:标准LED-通孔 T-1 3/4 RED CLR 20DG RoHS:否 制造商:Vishay Semiconductors 照明颜色:Red 光强度:0.7 mcd 波长/色温:615 nm 显示角:45 deg 透镜颜色/类型:Clear, Non-Diffused 正向电流:70 mA 正向电压:1.83 V to 3.03 V LED 大小:2 mm 系列: 封装:Tube
MV8104 功能描述:标准LED-通孔 T-1 3/4 RED CLR 20DG RoHS:否 制造商:Vishay Semiconductors 照明颜色:Red 光强度:0.7 mcd 波长/色温:615 nm 显示角:45 deg 透镜颜色/类型:Clear, Non-Diffused 正向电流:70 mA 正向电压:1.83 V to 3.03 V LED 大小:2 mm 系列: 封装:Tube
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*