- 您现在的位置：买卖IC网 > PDF目录45594 > MX10C8050FI (MACRONIX INTERNATIONAL CO LTD) 8-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP44 PDF资料下载
参数资料
| 型号： | MX10C8050FI |
| 厂商： | MACRONIX INTERNATIONAL CO LTD |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP44 |
| 封装： | PLASTIC, QFP-44 |
| 文件页数： | 10/14页 |
| 文件大小： | 147K |
| 代理商： | MX10C8050FI |
5
P/N:PM0804
REV. 0.0, APR. 23, 2001
MX10C8050X
Table 2. Status of the External Pins during Idle and Power Down
Mode
Program Memory
ALE
PSEN
PORT0
PORT1
PORT2
PORT3
Idle
Internal
1
Data
Idle
External
1
Float
Data
Address
Data
Power Down
Internal
0
Data
Power Down
External
0
Float
Data
POWER DOWN MODE
To save even more power, a Power Down mode can be
invoked by software. If this mode, the oscillator is stopped
and the instruction that invoked Power Down is the last
instruction executed. The on-chip RAM and Special
Function Registers retain their values until the Power
Down mode is terminated.
On the MX10C8050X either a hardware reset or an ex-
ternal interrupt can cause an exit from Power Down. Re-
set redefines all the SFRs but does not change the on-
chip RAM. An external interrupt allows both the SFRs
and on-chip RAM to retain their values.
ABSOLUTE MAXIMUM RATING*
Ambient Temperature Under Bias
-40°C to +85°C
Storage Temperature
-65°C to +150°C
Voltage on Any Other Pin to VSS
-0.5V to +6.5V
IOL Per I/O Pin
15mA
Power Dissipation
1.5W
(Based on PACKAGE heat transfer limitations, not de-
vice consumption)
IDLE MODE
The user's software can invoke the Idle Mode. When
the microcontroller is in this mode, power consumption
is reduced. The Special Function Registers and the
onboard RAM retain their values during Idle, but the pro-
cessor stops executing instructions. Idle Mode will be
exited if the chip is reset or if an enabled interrupt oc-
curs.
OPERATING CONDITIONS
Symbol
Description
Min
Max
Units
TA
Ambient Temperature Under Bias
Commerical
0
+70
°
C
Industrial
-40
+85
°
C
VCC
4.5
5.5
V
fOSC
Oscillator Frequency
3.5
40
MHz
To properly terminate Power Down, the reset or external
interrupt should not be executed before VCC is restored
to its normal operating level, and must be held active
long enough for the oscillator to restart and stabilize (nor-
mally less than 10 ms).
With an external interrupt, INT0 and INT1 must be en-
abled and configured as level-sensitive. Holding the pin
low restarts the oscillator but bringing the pin back high
completes the exit. Once the interrupt is serviced, the
next instruction to be executed after RETI will be the
one following the instruction that put the device into Power
Down.
相关PDF资料 |
PDF描述 |
|---|---|
| MX10C8051PC | 8-BIT, MROM, 40 MHz, MICROCONTROLLER, PDIP40 |
| MX10C8058FI | 8-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP44 |
| MX10C8058PI | 8-BIT, MROM, 40 MHz, MICROCONTROLLER, PDIP40 |
| MX10C8054FI | 8-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP44 |
| MX10C8058QC | 8-BIT, MROM, 40 MHz, MICROCONTROLLER, PQCC44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MX10C8050PC | 制造商:未知厂家 制造商全称:未知厂家 功能描述:SINGLE-CHIP 8-BIT MICROCONTROLLER |
| MX10C8050PI | 制造商:未知厂家 制造商全称:未知厂家 功能描述:SINGLE-CHIP 8-BIT MICROCONTROLLER |
| MX10C8050QC | 制造商:未知厂家 制造商全称:未知厂家 功能描述:SINGLE-CHIP 8-BIT MICROCONTROLLER |
| MX10C8050QI | 制造商:未知厂家 制造商全称:未知厂家 功能描述:SINGLE-CHIP 8-BIT MICROCONTROLLER |
| MX10C8051FC | 制造商:未知厂家 制造商全称:未知厂家 功能描述:SINGLE-CHIP 8-BIT MICROCONTROLLER |
发布紧急采购，3分钟左右您将得到回复。