- 您现在的位置：买卖IC网 > PDF目录69041 > MX10FMAXDQC (MACRONIX INTERNATIONAL CO LTD) 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQCC44 PDF资料下载
参数资料
| 型号： | MX10FMAXDQC |
| 厂商： | MACRONIX INTERNATIONAL CO LTD |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQCC44 |
| 封装： | PLASTIC, MS-016A, LCC-44 |
| 文件页数： | 22/26页 |
| 文件大小： | 466K |
| 代理商： | MX10FMAXDQC |
5
MX10FMAXDQC
Specifications subject to change without notice, contact your sales representatives for the most update information.
MX10FMAXDPC
REV. 1.1, MAR. 29, 2005
If desired, ALE operation can be disabled by setting bit 5
of SFR location 87H (PCON). With this bit set, the pin is
weakly pulled high. However, the ALE disable feature
will be suspended during a MOVX or MOVC instruction,
idle mode, power down mode. The ALE disable feature
will be terminated by reset. When the ALE disable fea-
ture is suspended or terminated, the ALE pin will no
longer be pulled up weakly. Setting the ALE-disable bit
has no affect if the micrcontroller is in external execu-
tion mode.
Throughout the remainder of this data sheet, ALE will
refer to the signal coming out of the ALE pin, and the pin
will be referred to as the ALE pin.
PSEN : Program Store Enable is the read strobe to ex-
ternal Program Memory.
When the MX10FMAX is executing code from external
Program memory, PSEN is activated twice each ma-
chine cycle, except that two PSEN activations are
skipped during each access to external Data memory.
EA/VPP : Extrernal Access enable. EA must be strapped
to VSS in order to enable the twiceto fetch code from
external Program Memory locations 0000H to 0FFFFH.
EA will be internally latched on reset.
EA should be strapped to VCC for internal program ex-
ecutions.
XTAL1 : Input to the inverting oscillator amplifier.
XTAL2 : Output from the inverting oscillator amplifier.
OSCILLATOR CHARACTERISTICS
XTAL1 and XTAL2 are the input and output, respectively,
of a inverting amplifier which can be configured for use
as an on-chip oscillator, as shown in Figure 3. Either a
quartz crystal or ceramic resonator may be used.
To drive the device from an external clock source, XTAL1
should be driven, while XTAL2 floats, as shown in Fig-
ure 4. There are no requirememts on the duty cycle of
the external clock signal, since the input to the internal
clocking circuitry is through a divide-by-two flip-flop, but
minimum and maximum high and low times specified
on the data sheet must be observed.
An external oscillator may encounter as much as a 100
pF load at XTAL1 when it starts up. This is due to inter-
action between the amplifer and its feedback capaci-
tance. Once the external signal meets the VIL and VIH
specifications the capacitance will not exceed 20 pF.
N/C
XTAL1
VSS
XTAL2
EXTERNAL
OSCILLATOR
SIGNAL
Figure 4. External Clock Drive Configuration
C2
XTAL2
XTAL1
VSS
Figure 3. Oscillator Connections
C1, C2 = 30 pF is equal to or less than 10 pF for Crystal
For Ceramic Resonators,contact resonator manufacture.
C1
相关PDF资料 |
PDF描述 |
|---|---|
| MX98216EC | 16 CHANNEL(S), 100M bps, LOCAL AREA NETWORK CONTROLLER, PQFP208 |
| MX98902AQC | 2 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQCC84 |
| P024T048T12AL | 1-OUTPUT 120 W DC-DC REG PWR SUPPLY MODULE |
| P048T048M12AL | 1-OUTPUT 120 W DC-DC REG PWR SUPPLY MODULE |
| P048F048M12AL | 1-OUTPUT 120 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MX-10G | 制造商:未知厂家 制造商全称:未知厂家 功能描述:MX |
| MX-10GC | 制造商:未知厂家 制造商全称:未知厂家 功能描述:MX |
| MX-10N | 制造商:未知厂家 制造商全称:未知厂家 功能描述:MX |
| MX10-SG-PC2-1E-5000 | 制造商:Japan Aviation Electronics (JAE) 功能描述:SOLD PER REEL |
| MX11 | 制造商:Lovato Electric Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。