- 您现在的位置：买卖IC网 > PDF目录240371 > MX152-25-512-U-H SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER PDF资料下载
参数资料
| 型号： | MX152-25-512-U-H |
| 元件分类： | 编、解码器及复用、解复用 |
| 英文描述： | SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| 文件页数： | 3/3页 |
| 文件大小： | 256K |
| 代理商： | MX152-25-512-U-H |
BEI Industrial Encoders
MX15 Series— Modular Incremental
Rotary Optical Encoder
Installation Instructions for MX15 Series Encoders
Preparation:
1. Inspect motor interface per MX15 Data Sheet or specification drawing.
2. Motor shaft must be free of burrs and other surface defects.
Installation:
1. Motor shaft should NOT be rotating during initial encoder installation.
2. Hold encoder perpendicular to motor shaft. Guide the encoder onto the motor shaft, pushing
encoder STRAIGHT on until it is flush against the motor surface. Do NOT rock side to side.
3. Install two #2-56 mount screws. Do not fully tighten at this point. (Note: A thread sealant should
be applied to the screw threads.)
4. Rotate the motor shaft (300 RPM, minimum). Insert push pin into the 1/16 hole in top of encoder
and press until pin bottoms out on encoder cover momentarily, then remove pin. CAUTION: DO
NOT press the push pin while motor shaft is stationary. Pin should only be pressed for one or two
seconds while shaft is rotating.
5. Fully tighten mounting screws. (recommended torque is 20 to 25 ounce inches.)
6. This completes the mechanical installation. Proceed with electrical connections as indicated on
product data sheet or specification drawing.
Removal:
1. Motor shaft may be stationary or rotating up to 1000 RPM during encoder removal.
2. Remove two mounting screws.
3. Grasp encoder firmly and pull STRAIGHT off the motor shaft. Do NOT rock side to side.
Tel: 805-968-0782 /800-350-2727 | Fax: 805-968-3154 /800-960-2726 | 7230 Hollister Ave., Goleta, CA 93117-2807 | www.beiied.com
Specification No. 924-02121-001 Rev.11-09
These commodities, technology or software if exported from the United States must be in accordance with the Bureau of
Industry, and Security, Export Administration regulations. Diversion contrary to U.S law is prohibited.
相关PDF资料 |
PDF描述 |
|---|---|
| MX153-38-512-G-H | SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| MX156-6M-1000-U-P | SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| MCT277-X001 | 1 CHANNEL TRANSISTOR OUTPUT OPTOCOUPLER |
| MCT2 | 1 CHANNEL TRANSISTOR OUTPUT OPTOCOUPLER |
| MC74AC4040DTR2 | AC SERIES, ASYN NEGATIVE EDGE TRIGGERED 12-BIT UP BINARY COUNTER, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MX-1530A/U | 制造商: 功能描述: 制造商:Kings Electronics 功能描述: 制造商:undefined 功能描述: |
| MX-1531/U | 制造商:TE Connectivity 功能描述: |
| MX-1531A/U | 制造商:Kings Electronics 功能描述: |
| MX153-25-1000-U-T | 功能描述:编码器 0.25" BORE 1000PPR RoHS:否 制造商:Avago Technologies 产品:Optical Encoders 类型:Absolute 每转脉冲: 制动器数量: 通道数量:2 安装风格:Through Hole 端接类型:Solder Pin 输出: 轴类型: 带开关: 电源电压:5 V 工作温度范围:- 40 C to + 115 C |
| MX153-25-1024-U-T | 功能描述:编码器 0.25" BORE 1024PPR RoHS:否 制造商:Avago Technologies 产品:Optical Encoders 类型:Absolute 每转脉冲: 制动器数量: 通道数量:2 安装风格:Through Hole 端接类型:Solder Pin 输出: 轴类型: 带开关: 电源电压:5 V 工作温度范围:- 40 C to + 115 C |
发布紧急采购，3分钟左右您将得到回复。