- 您现在的位置：买卖IC网 > PDF目录11653 > MXB7846EEE+T (Maxim Integrated Products)IC CNTRLR TOUCH RES 16QSOP PDF资料下载
参数资料
| 型号： | MXB7846EEE+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/24页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR TOUCH RES 16QSOP |
| 其它有关文件： | Automotive Product Guide |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 温度传感器 |
| 输入类型： | 模拟 |
| 输出类型： | 数字 |
| 接口： | 4 线 |
| 电流 - 电源： | 950µA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 带卷 (TR) |
MXB7846
2.375V to 5.25V, 4-Wire Touch-Screen Controller
with Internal Reference and Temperature Sensor
20
______________________________________________________________________________________
2) The MXB7846’s
CS pin is driven low by the TMS320’s
XF I/O port to enable data to be clocked into the
MXB7846’s DIN pin.
3) An 8-bit word (1XXXXXXX) should be written to the
MXB7846 to initiate a conversion and place the
device into normal operating mode. See Table 3 to
select the proper XXXXXXX bit values for your spe-
cific applications.
4) The MXB7846’s BUSY output is monitored through
the TMS320’s FSR input. A falling edge on the BUSY
output indicates that the conversion is in progress
and data is ready to be received from the device.
5) The TMS320 reads in 1 data bit on each of the next
16 rising edges of DCLK. These bits represent the
12-bit conversion result followed by 4 trailing bits.
6) Pull
CS high to disable the MXB7846 until the next
conversion is initiated.
Layout, Grounding, and Bypassing
For best performance, use printed circuit (PC) boards
with good layouts; wire-wrap boards are not recommend-
ed. Board layout should ensure that digital and analog
signal lines are separated from each other. Do not run
analog and digital (especially clock) lines parallel to one
another, or digital lines underneath the ADC package.
Establish a single-point analog ground (star ground
point) at GND. Connect all analog grounds to the star
ground. Connect the digital system ground to the star
ground at this point only. For lowest noise operation,
minimize the length of the ground return to the star
ground’s power supply.
Power-supply decoupling is also crucial for optimal
device performance. A good way to decouple analog
supplies is to place a 10F tantalum capacitor in paral-
lel with a 0.1F capacitor bypassed to GND. To maxi-
mize performance, place these capacitors as close as
possible to the supply pin of the device. Minimize
capacitor lead length for best supply-noise rejection. If
the supply is very noisy, a 10Ω resistor can be connect-
ed in series as a lowpass filter.
While using the MXB7846, the interconnection between
the converter and the touch screen should be as short
as possible. Since touch screens have low resistance,
longer or loose connections may introduce error. Noise
can also be a major source of error in touch-screen
applications (e.g., applications that require a backlight
LCD panel). EMI noise coupled through the LCD panel
to the touch screen may cause flickering of the convert-
ed data. Utilizing a touch screen with a bottom-side
metal layer connected to ground decouples the noise
to ground. In addition, the filter capacitors from Y+, Y-,
X+, and X- inputs to ground also help further reduce
the noise. Caution should be observed for settling time
of the touch screen, especially operating in the single-
ended measurement mode and at high data rates.
Definitions
Integral Nonlinearity
Integral nonlinearity (INL) is the deviation of the values
on an actual transfer function from a straight line. This
straight line can be either a best-straight-line fit or a line
drawn between the endpoints of the transfer function,
once offset and gain errors have been nullified. The
static linearity parameters for the MXB7846 are mea-
sured using the end-point method.
MXB7846
CS
DIN
BUSY
HIGH IMPEDANCE
DOUT
DCLK
START
A2
A1
A0
MODE
SER/DEF
PD1
PD0
MSB
B10
B1
B0
Figure 16. MXB7846-to-TMS320 Serial Interface Timing Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| V24C28M100BG | CONVERTER MOD DC/DC 28V 100W |
| PCF51JM128VLH | MCU 32BIT 128K FLASH 64-LQFP |
| V24C28M100B | CONVERTER MOD DC/DC 28V 100W |
| MC9S08LC36LH | IC MCU 36K FLASH 2K RAM 64-LQFP |
| V24C24M100BL3 | CONVERTER MOD DC/DC 24V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MXB7846EUE | 功能描述:触摸屏转换器和控制器 RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
| MXB7846EUE+ | 功能描述:触摸屏转换器和控制器 2.375-5.25V 4-Wire Touch-Screen Ctlr RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
| MXB7846EUE+T | 功能描述:触摸屏转换器和控制器 2.375-5.25V 4-Wire Touch-Screen Ctlr RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
| MXB7846EUE-T | 功能描述:触摸屏转换器和控制器 RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
| MXB7846EVC16 | 功能描述:数据转换 IC 开发工具 MXB7846C16 Eval Kit RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
发布紧急采购，3分钟左右您将得到回复。