- 您现在的位置：买卖IC网 > PDF目录188959 > N2593MK120 (WESTCODE SEMICONDUCTORS LTD) 5135 A, 1200 V, SCR PDF资料下载
参数资料
| 型号： | N2593MK120 |
| 厂商： | WESTCODE SEMICONDUCTORS LTD |
| 元件分类： | 晶闸管 |
| 英文描述： | 5135 A, 1200 V, SCR |
| 文件页数： | 5/11页 |
| 文件大小： | 272K |
| 代理商： | N2593MK120 |
WESTCODE
WESTCODE An IXYS Company
Wespack Phase Control Thyristor Types N2593MK120 to N2593MK180
Provisional Data Sheet. Types N2593MK120 to N2593MK180 Issue 1
Page 3 of 11
July, 2005
Notes on Ratings and Characteristics
1.0 Voltage Grade Table
Voltage Grade
VDRM VDSM VRRM
V
VRSM
V
VD VR
DC V
12
1200
1300
810
14
1400
1500
930
16
1600
1700
1040
18
1800
1900
1150
2.0 Extension of Voltage Grades
This report is applicable to other voltage grades when supply has been agreed by Sales/Production.
3.0 De-rating Factor
A blocking voltage de-rating factor of 0.13%/°C is applicable to this device for Tj below 25°C.
4.0 Repetitive dv/dt
Standard dv/dt is 1000V/s.
5.0 Snubber Components
When selecting snubber components, care must be taken not to use excessively large values of snubber
capacitor or excessively small values of snubber resistor. Such excessive component values may lead to
device damage due to the large resultant values of snubber discharge current. If required, please consult
the factory for assistance.
6.0 Rate of rise of on-state current
The maximum un-primed rate of rise of on-state current must not exceed 400A/s at any time during turn-
on on a non-repetitive basis. For repetitive performance, the on-state rate of rise of current must not
exceed 200A/s at any time during turn-on. Note that these values of rate of rise of current apply to the
total device current including that from any local snubber network.
7.0 Gate Drive
The nominal requirement for a typical gate drive is illustrated below. An open circuit voltage of at least 30V
is assumed. This gate drive must be applied when using the full di/dt capability of the device.
IGM
IG
tp1
4A/s
The magnitude of IGM should be between five and ten times IGT, which is shown on page 2. Its duration
(tp1) should be 20s or sufficient to allow the anode current to reach ten times IL, whichever is greater.
Otherwise, an increase in pulse current could be needed to supply the necessary charge to trigger. The
‘back-porch’ current IG should remain flowing for the same duration as the anode current and have a
magnitude in the order of 1.5 times IGT.
相关PDF资料 |
PDF描述 |
|---|---|
| N2593MK140 | 5135 A, 1400 V, SCR |
| N2593MK160 | 5135 A, 1600 V, SCR |
| N2593MK180 | 5135 A, 1800 V, SCR |
| N275PH02-08 | 355 A, 200 V, SCR |
| N2880-A | POWER TRANSFORMER, 175 VA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| N2596G | 制造商:未知厂家 制造商全称:未知厂家 功能描述:150 KHz 3A Step-Down Switching Voltage Regulator (SVR) |
| N2596G-5 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:150 KHz 3A Step-Down Switching Voltage Regulator (SVR)-Preliminary |
| N2596SG | 制造商:未知厂家 制造商全称:未知厂家 功能描述:150 KHz 3A Step-Down Switching Voltage Regulator (SVR) |
| N2596SG-5 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:150 KHz 3A Step-Down Switching Voltage Regulator (SVR)-Preliminary |
| N2596TG | 制造商:未知厂家 制造商全称:未知厂家 功能描述:150 KHz 3A Step-Down Switching Voltage Regulator (SVR) |
发布紧急采购，3分钟左右您将得到回复。