参数资料
型号: N80C32-33
厂商: INTEL CORP
元件分类: 微控制器/微处理器
英文描述: CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
中文描述: 8-BIT, 33 MHz, MICROCONTROLLER, PQCC44
封装: PLASTIC, LCC-44
文件页数: 5/23页
文件大小: 319K
代理商: N80C32-33
8XC52/54/58
If desired, ALE operation can be disabled by setting
bit 0 of SFR location 8EH. With this bit set, the pin is
weakly pulled high. However, the ALE disable fea-
ture will be suspended during a MOVX or MOVC in-
struction, idle mode, power down mode and ICE
mode. The ALE disable feature will be terminated by
reset. When the ALE disable feature is suspended or
terminated, the ALE pin will no longer be pulled up
weakly. Setting the ALE-disable bit has no affect if
the microcontroller is in external execution mode.
Throughout the remainder of this data sheet, ALE
will refer to the signal coming out of the ALE/PROG
pin, and the pin will be referred to as the ALE/PROG
pin.
PSEN:
Program Store Enable is the read strobe to
external Program Memory.
When the 8XC5X is executing code from external
Program Memory, PSEN is activated twice each
machine cycle, except that two PSEN activations
are skipped during each access to external Data
Memory.
EA/V
PP
:
External Access enable. EA must be
strapped to VSS in order to enable the device to
fetch code from external Program Memory locations
0000H to 0FFFFH. Note, however, that if any of the
Lock bits are programmed, EA will be internally
latched on reset.
EA should be strapped to V
CC
for internal program
executions.
This pin also receives the programming supply volt-
age (V
PP
) during EPROM programming.
XTAL1:
Input to the inverting oscillator amplifier.
XTAL2:
Output from the inverting oscillator amplifi-
er.
OSCILLATOR CHARACTERISTICS
XTAL1 and XTAL2 are the input and output, respec-
tively, of a inverting amplifier which can be config-
ured for use as an on-chip oscillator, as shown in
Figure 3. Either a quartz crystal or ceramic resonator
may be used. More detailed information concerning
the use of the on-chip oscillator is available in Appli-
cation Note AP-155, ‘‘Oscillators for Microcontrol-
lers’’, Order No. 230659.
272336–5
C1, C2
e
30 pF
g
10 pF for Crystals
For Ceramic Resonators, contact resonator manufac-
turer.
Figure 3. Oscillator Connections
To drive the device from an external clock source,
XTAL1 should be driven, while XTAL2 floats, as
shown in Figure 4. There are no requirements on the
duty cycle of the external clock signal, since the in-
put to the internal clocking circuitry is through a di-
vide-by-two flip-flop, but minimum and maximum
high and low times specified on the data sheet must
be observed.
An external oscillator may encounter as much as a
100 pF load at XTAL1 when it starts up. This is due
to interaction between the amplifier and its feedback
capacitance. Once the external signal meets the V
IL
and V
IH
specifications the capacitance will not ex-
ceed 20 pF.
272336–6
Figure 4. External Clock Drive Configuration
IDLE MODE
The user’s software can invoke the Idle Mode. When
the microcontroller is in this mode, power consump-
tion is reduced. The Special Function Registers and
the onboard RAM retain their values during Idle, but
the processor stops executing instructions. Idle
Mode will be exited if the chip is reset or if an en-
abled interrupt occurs.
5
相关PDF资料
PDF描述
N80C52 CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
N80C52-1 CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
N80C52-2 CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
N80C52-24 CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
N80C52-33 CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
相关代理商/技术参数
参数描述
N80C325 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller
N80C32T2-1 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller
N80C42 制造商:INTEL 制造商全称:Intel Corporation 功能描述:UNIVERSAL PERIPHERAL INTERFACE CHMOS 8-BIT SLAVE MICROCONTROLLER
N80C452 制造商:Rochester Electronics LLC 功能描述:- Bulk
N80C452-14 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller