参数资料
| 型号： | NA555S-13 |
| 厂商： | Diodes Inc |
| 文件页数： | 12/14页 |
| 文件大小： | 0K |
| 描述： | IC OSC MONO TIMING SO8 |
| 特色产品： | Precision Timer ICs |
| 标准包装： | 1 |
| 类型： | 555 型，计时器/振荡器（单路） |
| 频率： | 500kHz |
| 电源电压： | 4.5 V ~ 16 V |
| 电流 - 电源： | 13mA |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 标准包装 |
| 供应商设备封装： | 8-SO |
| 安装类型： | 表面贴装 |
| 其它名称： | NA555S-13DIDKR |
NE555/SA555/NA555
PRECISION TIMERS
NE555/SA555/NA555
Document number: DS35112 Rev. 4 - 2
7 of 14
February 2012
Diodes Incorporated
NEW
PROD
UC
T
Typical Applications Characteristics
Monostable Operation
For monostable operation, any of the ‘555 timers can be connected as shown in Figure 1. If the output is low, application of a
negative-going pulse to the trigger (TRIG) sets the internal flip-flop and drives the output high. Capacitor C is then charged
through RA until the voltage across the capacitor reaches the threshold voltage of the threshold (THRES) input. If TRIG has
returned to a high level, the output of the threshold comparator resets the internal flip-flop, drives the output low, and
discharges C.
Fig 1. Monostable operation
Monostable operation is initiated when TRIG voltage falls below the trigger threshold. Once initiated, the sequence ends only
if TRIG is high for at least 10
μs before the end of the timing interval. When the trigger is grounded, the comparator storage
time can be as long as 10
μs, which limits the minimum monostable pulse width to 10μs. Because of the threshold level and
saturation voltage of Q1, the output pulse duration is approximately tW = 1.1RAC. Figure 3 is a plot of the time constant for
various values of RA and C. The threshold levels and charge rates both are directly proportional to the supply voltage, VCC.
The timing interval is, therefore, independent of the supply voltage, so long as the supply voltage is constant during the time
interval.
Applying a negative-going trigger pulse simultaneously to RESET and TRIG during the timing interval discharges C and
reinitiates the cycle, commencing on the positive edge of the reset pulse. The output is held low as long as the reset pulse is
low. To prevent false triggering, when RESET is not used, it should be connected to VCC.
Fig. 2 Typical Monostable Waveforms
Fig. 3 Output Pulse Duration vs. Capacitance
RL
RA
THRES
TRIG
DISCH
RESET
CONT
VCC
GND
OUT
Output
4
7
6
2
1
3
8
5
VCC
(5V to 15V)
Input
C
相关PDF资料 |
PDF描述 |
|---|---|
| V28A5M175BF2 | CONVERTER MOD DC/DC 5V 75W |
| D38999/20SG11SN | CONN RCPT 11POS WALL MNT W/SCKT |
| V28A5M175BF | CONVERTER MOD DC/DC 5V 75W |
| V28A5M175BL | CONVERTER MOD DC/DC 5V 175W |
| VI-25B-IW-B1 | CONVERTER MOD DC/DC 95V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NA556 | 制造商:TI 制造商全称:Texas Instruments 功能描述:DUAL PRECISION TIMERS |
| NA556D | 功能描述:计时器和支持产品 Dual Prec Timers RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| NA556DG4 | 功能描述:计时器和支持产品 Dual Prec Timers RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| NA556DR | 功能描述:计时器和支持产品 Dual Prec Timers RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| NA556DRG4 | 功能描述:计时器和支持产品 Dual Prec Timers RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。