参数资料
| 型号： | NB7N017MEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 3/5页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL BBG NB7N017MMN |
| 标准包装： | 1 |
| 系列： | * |
NB7N017MEVB
Power Supplies
The NB7N017M is powered by |V CC ? V EE | = 3.3 V
power supplies. For straightforward lab setup operation,
negative voltages is recommended to enable the 50 W
internal impedance of the oscilloscope to be used as a
termination for the CML signals (V CC = 0.0 V, V EE = ? 3.3 V
and GND = 0.0 V).
It is recommended to add capacitors (C4 and C8 are 22 m F
and C1, C2, C3, C5, C6, and C7 are 0.1 m F) to reduce the
unwanted noise from the power supplies. Adding capacitors
can improve the edge rates, reduce over shoot, and under
shoot. Evaluation board provides several capacitor pads to
add capacitors.
Termination
CML outputs need to be terminated to V CC via a 50 W
resistor. The input pins contain internal 50 W resistors
(VT pins). The VT pins are tied to V CC which limits the
input configuration of this device on this evaluation board.
NOTE: The test measurement device must contain 50 W
termination.
1. Connect appropriate power supplies. (V CC = 0.0 V,
V EE = ? 3.3 V, and GND = 0.0 V).
2. Connect input signals to the appropriate SMA
connectors. Configure input signals according to
the device data sheet.
3. Connect a test measurement device on the device
output SMA connectors.
Power Supply
V CC GND V EE
CML
CE Input
CML
CLK Input
NB7N017M
CML TC Output
Test Measuring
Equipment
Channel 1
Channel 2
CML
SEL Input
Dip Switch
for Pa[0:8]
and Pb[0:8]
Figure 4. Typical Lab Setup
http://onsemi.com
3
相关PDF资料 |
PDF描述 |
|---|---|
| NC2003SR | STAND NOTEBOOK W/2FANS USB |
| NCN9252MUGEVB | BOARD EVALUATION NCN9252MU |
| NCP1031POEEVB | BOARD EVAL NCP1031 POE DC CONV |
| NCP1605LCDTVGEVB | BOARD EVAL NCP1605/1396 |
| NCP1608BOOSTGEVB | BOARD EVAL NCP1608 100W BOOST |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NB7N017MMN | 功能描述:预定标器 BBG 8BT DL MOD RoHS:否 制造商:ON Semiconductor 最大工作频率:1100 MHz 最小工作频率:100 MHz 电源电压-最小:4.5 V 电源电压-最大:5.5 V 工作电源电压:5 V 最小工作温度:- 40 C 最大工作温度:+ 85 C 封装:Tube |
| NB7N017MMNG | 功能描述:预定标器 BBG 8BT DL MOD RoHS:否 制造商:ON Semiconductor 最大工作频率:1100 MHz 最小工作频率:100 MHz 电源电压-最小:4.5 V 电源电压-最大:5.5 V 工作电源电压:5 V 最小工作温度:- 40 C 最大工作温度:+ 85 C 封装:Tube |
| NB7N017MMNR2 | 功能描述:预定标器 BBG 8BT DL MOD RoHS:否 制造商:ON Semiconductor 最大工作频率:1100 MHz 最小工作频率:100 MHz 电源电压-最小:4.5 V 电源电压-最大:5.5 V 工作电源电压:5 V 最小工作温度:- 40 C 最大工作温度:+ 85 C 封装:Tube |
| NB7N017MMNR2G | 功能描述:预定标器 3.3V SiGe 8-Bit Dual 预定标器/Divider RoHS:否 制造商:ON Semiconductor 最大工作频率:1100 MHz 最小工作频率:100 MHz 电源电压-最小:4.5 V 电源电压-最大:5.5 V 工作电源电压:5 V 最小工作温度:- 40 C 最大工作温度:+ 85 C 封装:Tube |
| NB7V32M | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:1.8V / 2.5V, 10GHz ÷2 Clock Divider with CML Outputs |
发布紧急采购，3分钟左右您将得到回复。