- 您现在的位置：买卖IC网 > PDF目录19673 > NCP1011ST130T3G (ON Semiconductor)IC OFFLINE SWIT SMPS CM SOT223 PDF资料下载
参数资料
| 型号： | NCP1011ST130T3G |
| 厂商： | ON Semiconductor |
| 文件页数： | 16/24页 |
| 文件大小： | 0K |
| 描述： | IC OFFLINE SWIT SMPS CM SOT223 |
| 标准包装： | 1 |
| 输出隔离： | 隔离 |
| 频率范围： | 117kHz ~ 143kHz |
| 输入电压： | 8.5 V ~ 10 V |
| 输出电压： | 700V |
| 功率（瓦特）： | 19W |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | TO-261-4，TO-261AA |
| 供应商设备封装： | SOT-223 |
| 包装： | 剪切带 (CT) |
| 其它名称： | NCP1011ST130T3GOSCT |
NCP1010, NCP1011, NCP1012, NCP1013, NCP1014
Design Procedure
The design of an SMPS around a monolithic device does
not differ from that of a standard circuit using a controller
and a MOSFET. However, one needs to be aware of certain
characteristics specific of monolithic devices:
350
250
150
50.0
> 0 !!
--50.0
1.004M
1.011M
1.018M
1.025M
1.032M
Figure 26. The Drain--Source Wave Shall Always be Positive . . .
Lp · Ip
ton =
N · (Vout + Vf)
. toff, the OFF time is thus:
Lp · Ip
toff =
1. In any case, the lateral MOSFET body--diode shall
never be forward biased, either during startup
(because of a large leakage inductance) or in
normal operation as shown by Figure 26.
As a result, the Flyback voltage which is reflected on the
drain at the switch opening cannot be larger than the input
voltage. When selecting components, you thus must adopt
a turn ratio which adheres to the following equation:
N · (Vout + Vf) < Vin min (eq. 14) . For instance, if
operating from a 120 V DC rail, with a delivery of 12 V, we
can select a reflected voltage of 100 Vdc maximum:
120–100 > 0. Therefore, the turn ratio Np:Ns must be
smaller than 100/(12 + 1) = 7.7 or Np:Ns < 7.7. We will see
later on how it affects the calculation.
2. A current--mode architecture is, by definition,
sensitive to subharmonic oscillations.
Subharmonic oscillations only occur when the
SMPS is operating in Continuous Conduction
Mode (CCM) together with a duty--cycle greater
than 50%. As a result, we recommend to operate
the device in DCM only, whatever duty--cycle it
implies (max = 65%). However, CCM operation
with duty--cycles below 40% is possible.
3. Lateral MOSFETs have a poorly dopped
body--diode which naturally limits their ability to
sustain the avalanche. A traditional RCD clamping
network shall thus be installed to protect the
MOSFET. In some low power applications,
a simple capacitor can also be used since
Lf
Vdrain max = Vin + N · (Vout + Vf) + Ip · ? Ctot
(eq. 15) , where Lf is the leakage inductance,
Ctot is the total capacitance at the drain node
(which is increased by the capacitor wired between
drain and source), N the Np:Ns turn ratio, Vout the
output voltage, Vf the secondary diode forward
drop and finally, Ip the maximum peak current.
Worse case occurs when the SMPS is very close to
regulation, e.g. the Vout target is almost reached
and Ip is still pushed to the maximum.
Taking into account all previous remarks, it becomes
possible to calculate the maximum power that can be
transferred at low line.
When the switch closes, Vin is applied across the primary
inductance Lp until the current reaches the level imposed by
the feedback loop. The duration of this event is called the ON
time and can be defined by:
(eq. 16)
Vin
At the switch opening, the primary energy is transferred
to the secondary and the flyback voltage appears across
Lp, resetting the transformer core with a slope of
Lp
(eq. 17)
N · (Vout + Vf)
If one wants to keep DCM only, but still need to pass the
maximum power, we will not allow a dead--time after the
core is reset, but rather immediately restart. The switching
time can be expressed by:
1 1
Tsw = toff + ton = Lp · Ip · ? Vin + N · (Vout + Vf) ?
(eq. 18)
http://onsemi.com
16
相关PDF资料 |
PDF描述 |
|---|---|
| ABE40DHRD | CONN CARD EXTEND 80POS 1MM SLD |
| GCM15DCMI | CONN EDGECARD 30POS .156 SQ WW |
| MIC5213-2.8BC5 TR | IC REG LDO 2.8V 80MA SC70-5 |
| DEA1X3A100JC1B | CAP CER 10PF 1KV 5% RADIAL |
| TL-2100/S | BATT LITH AA 3.6V XTRA CYLINDER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1011ST65T3 | 功能描述:交流/直流开关转换器 Low Standby Power RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| NCP1011ST65T3G | 功能描述:电流型 PWM 控制器 Low Standby Power Monolithic Switcher RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1012 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Self-Supplied Monolithic Switcher for Low Standby- Power Offline SMPS |
| NCP1012/D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Self-Supplied Monolithic Switcher for Low Standby-Power Offline SMPS |
| NCP1012AP065 | 功能描述:电流型 PWM 控制器 Low Standby Power RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。