- 您现在的位置：买卖IC网 > PDF目录19679 > NCP1012APL100R2G (ON Semiconductor)IC OFFLINE SW SMPS CM OVP 7DIPGW PDF资料下载
参数资料
| 型号： | NCP1012APL100R2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 9/24页 |
| 文件大小： | 0K |
| 描述： | IC OFFLINE SW SMPS CM OVP 7DIPGW |
| 标准包装： | 1,000 |
| 输出隔离： | 隔离 |
| 频率范围： | 90kHz ~ 110kHz |
| 输入电压： | 8.5 V ~ 10 V |
| 输出电压： | 700V |
| 功率（瓦特）： | 19W |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 8-SMD（7 个接脚），鸥形翼 |
| 供应商设备封装： | 7-PDIP，鸥翼型 |
| 包装： | 带卷 (TR) |
NCP1010, NCP1011, NCP1012, NCP1013, NCP1014
8.00
6.00
4.00
Vcc
Device
8.5 V
7.5 V
2.00
Internally
Pulses
0
Startup Period
Figure 14. The Charge/Discharge Cycle Over a 10 m F V CC Capacitor
The protection burst duty--cycle can easily be computed
through the various timing events as portrayed by Figure 16.
Being loaded by the circuit consumption, the voltage on
the V CC capacitor goes down. When the DSS controller
detects that V CC has reached 7.5 V (VCC ON ), it activates the
internal current source to bring V CC toward 8.5 V and stops
again: a cycle takes place whose low frequency depends on
the V CC capacitor and the IC consumption. A 1.0 V ripple
takes place on the V CC pin whose average value equals
(VCC OFF + VCC ON )/2. Figure 14 portrays a typical
operation of the DSS.
As one can see, the V CC capacitor shall be dimensioned to
offer an adequate startup time, i.e. ensure regulation is
reached before V CC crosses 7.5 V (otherwise the part enters
the fault condition mode). If we know that Δ V = 1.0 V
for the presence of the error flag every time V CC crosses
VCC ON . If the error flag is low (peak limit not active) then
the IC works normally. If the error signal is active, then the
NCP101X immediately stops the output pulses, reduces its
internal current consumption and does not allow the startup
source to activate: V CC drops toward ground until it reaches
the so--called latch--off level, where the current source
activates again to attempt a new restart. When the error is
gone, the IC automatically resumes its operation. If the
default is still there, the IC pulses during 8.5 V down to 7.5 V
and enters a new latch--off phase. The resulting burst
operation guarantees a low average power dissipation and
lets the SMPS sustain a permanent short--circuit. Figure 15
shows the corresponding diagram.
and ICC1 (max) is 1.1 mA (for instance we selected an 11 Ω
device switching at 65 kHz), then the V CC capacitor can
4V
Current Sense
Information
ICC1 · tstartup (eq. 1) . Let’s
be calculated using: C ≥
Δ V
suppose that the SMPS needs 10 ms to startup, then we will
calculate C to offer a 15 ms period. As a result, C should be
greater than 20 m F thus the selection of a 33 m F/16 V
capacitor is appropriate.
FB
Division
Max
Ip
V CC
+
--
VCC ON
Signal
To
Latch
Reset
Short Circuit Protection
The internal protection circuitry involves a patented
arrangement that permanently monitors the assertion of an
internal error flag. This error flag is, in fact, a signal that
instructs the controller that the internal maximum peak
current limit is reached. This naturally occurs during the
startup period (Vout is not stabilized to the target value) or
Clamp
Active?
Flag
when the optocoupler LED is no longer biased, e.g. in a
short--circuit condition or when the feedback network is
broken. When the DSS normally operates, the logic checks
Figure 15. Simplified NCP101X Short--Circuit
Detection Circuitry
http://onsemi.com
9
相关PDF资料 |
PDF描述 |
|---|---|
| PSA15R-075P | ADAPTER WALL R-SERIES 15W 7.5V |
| MIC5210-2.7BMM TR | IC REG LDO 2.7V .15A 8-MSOP |
| 171-050-203L021 | CONN DB50 FEMALE SLD CUP NICKEL |
| MIC5210-2.7BMM | IC REG LDO 2.7V .15A 8-MSOP |
| V110A36E400BL | CONVERTER MOD DC/DC 36V 400W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1012APL130R | 制造商:ON Semiconductor 功能描述: |
| NCP1012APL130R2 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Self-Supplied Monolithic Switcher for Low Standby- Power Offline SMPS |
| NCP1012APL130R2G | 功能描述:电流型 PWM 控制器 Low Standby Power Monolithic Switcher RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1012GEVB | 功能描述:电源管理IC开发工具 NCP1012 SMPS SWITCHER EVB RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP1012ST100T3 | 功能描述:电流型 PWM 控制器 Low Standby Power RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。